詳細信息
SPECIFICATION | ||||||||||||
承認書 | ||||||||||||
DESIGNATION品名： | MODEL型號 | EDITION版本：01 | PAGE頁碼：1 of 2 | |||||||||
1. RATING額定值: | .DC48V0.2A | |||||||||||
2. OPERATIONTEMPERATURERANGE使用溫度範圍： | -30～+70℃ | |||||||||||
3.PRESERVATIVETEMPERATURERANGE保存溫度範圍： | -40～+85℃ | |||||||||||
4. CONSTRUCTION DIMENSION結構尺寸： | Apply to the appended drawing： 符合附加圖紙 | |||||||||||
ITEM項目 | TEST CONDITION測試條件 | SPECIFICATION規格 | ||||||||||
5. ELECTRONICAL CHARACTERISTICS.電氣性能. | ||||||||||||
5A | CONTACT RESISTANCE 接觸阻抗 | Being measured at 1KHz small current contact resistance meter. 在1KHZ小電流下測量. | 30MΩmax 30毫歐以下. | |||||||||
5B | INSULATION RESISTANCE 絕緣阻抗 | Measurements shall be made following application of DC100V potential across terminals and across terminals and frame for 1 minute. 在端子之間和端子與殼之間加DC100V條件下,持續1分鐘測量. | 100MΩmin 100兆歐以上. | |||||||||
5C | WITHSTAND VOLTAGE 耐電壓 | AC500V (50Hz or 60Hz) shall be applied across terminals and across terminals and frame for one minute 在端子之間和端子與殼之間加AC500V(50HZ或60HZ)條件下,持續1分鐘測量. | There shall be no breakdown. 無擊穿現象出現. | |||||||||
6. MECHANICAL CHARACTERISTICS.機械性能. | ||||||||||||
6A | ACTIONPOWER 動作力 | Action Power 5-25N 動作力 5-25N | ||||||||||
6B | TERMINAL STRENGTH 端子強度 | A static force of 500gf being applied in one direction on the tip of terminal for 1 minute. 一個500克之靜負荷施加於端子頂部的一個方向持續1分鐘。 | There shall be no sign of damage mechanically and electrically. 無任何跡象顯示機械及電氣性能之損壞. | |||||||||
7. DURABILITY.耐久性. | ||||||||||||
7A | SOLDERING TEST. 可焊性試驗 | The tip of the terminals shall be dipped 2mm in the solder bath at a temperature of 250±5℃for2±0.5sec.端子頂部被浸入焊錫池2mm深,溫度230±5℃時間2±0.5秒。 | A new uniform coating of solder shall cover a minimum of90of the surface being immersed.浸入的部分90%以上表面將被錫覆蓋. | |||||||||
7B | RESISTANCE TOSOLDERING HEAT 耐焊接熱 | Soldering area:t/2 of P.C.B thickness焊接面積：印刷基板的1/2厚度處 temperature:260±5℃Sinkingtime: 5±1S.焊接溫度：250±5℃，焊接時間：5±1秒。 | No damage (electrical and mechanical) 無異常。（電氣、機械特性） | |||||||||
EDITION 版本 | DATE 日期 | WRTN 制定 | CHKD 審核 | APVD 批準 | DESCRIPTIONS 備註 | |||||||
01 | Lerble | |||||||||||
SPECIFICATION
承認書
DESIGNATION品名： | MODEL型號： | EDITION版本：01 | PAGE頁碼：2of 2 | ||||||||||
ITEM項目 | TEST CONDITION測試條件 | SPECIFICATION規格 | |||||||||||
7C | LIFE TEST. 壽命試驗 | 5,000 cycles of operation at a rate of60cycles per minute with unloading. 無負載條件下,每分鐘30次的速度操作5,000次。 | (1). Contact resistance .200mΩmax接觸阻抗200毫歐以下. (2). Insertion and withdraw force±30 initial value插拔力變化範圍初始值±30% (3). ITEM專案-5B (4). ITEM專案-5C (5). ITEM專案-6B | ||||||||||
7D | HEAT TEST. 耐熱試驗 | 85±2℃for96hours after test keep in normal condition for60minutes. 在85±2℃環境中放96小時,再放在正常環境中60分鐘後進行測試。 | (1). Contact resistance 50mΩmax.接觸電阻200毫歐以下 (2). Insulation resistance. 50MΩmin.絕緣電阻100兆歐以上 (3). There shall be no sign of damage mechanically and electrically.無任何跡象顯示機械及電器性能之損壞. | ||||||||||
7E | HUMIDITY TEST. 耐濕試驗 | The condition of temperature60±2℃and humidty 90-95%for96hrs. after test keep in normal condition for60min. 在溫度60±2℃，濕度90-95%環境中放96小時,再放在正常環境中60分鐘後進行測試。 | |||||||||||
7F | COLD TEST. 耐冷試驗 | At –40±2℃for96hrs. after test keep in normal condition for60min. 在-40±2℃環境中放96小時,再置於正常環境中60分鐘後進行測試。 | |||||||||||
7G | SALTSPRAYTEST 鹽霧試驗 | At 5% Nacl liquor for12hours, after washing, keep in normal condition for 30 min. 浸入5%的Nacl溶液中12小時，用水清洗並 在室溫下放置30分鐘 | Without excessive Corrosion or crack in appearance 表面無明顯腐蝕或裂紋 | ||||||||||
8. STANDARD CONDITION試驗、測定狀態 | |||||||||||||
Unless otherwise specified, the test and measurements shall be carried out as follows: Ambient temperature溫度：5-35℃ Relative humidity相對濕度：45~85% Air pressure氣壓：86~106kPa(860~1060mbar) However if doubt arises on the decision based on the measured values under the above-mentioned conditions, the following condition shall be employed:但在對判定産生疑義時，按下述狀態實施： Ambient temperature溫度：20±2℃ Relative humidity相對濕度：65±5% Air pressure氣壓：86~106kPa(860~1060mbar) | |||||||||||||
EDITION 版本 | DATE 日期 | WRTN 制定 | CHKD 審核 | APVD 批準 | DESCRIPTIONS 備註 | ||||||||
01 | Lerble | ||||||||||||