- 您現在的位置：買賣IC網 > PDF目錄373912 > AD7569TE (ANALOG DEVICES INC) LC2MOS Complete, 8-Bit Analog I/0 Systems PDF資料下載
參數資料
| 型號： | AD7569TE |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | LC2MOS Complete, 8-Bit Analog I/0 Systems |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, CQCC28 |
| 封裝： | CERAMIC, LCC-28 |
| 文件頁數： | 10/20頁 |
| 文件大小： | 504K |
| 代理商： | AD7569TE |
–10–
REV. B
AD7569/AD7669
INTERNAL CLOCK
Clock pulses are generated by the action of an internal current
source charging the external capacitor (C
CLK
) and this external
capacitor discharging through the external resistor (R
CLK
).
When a conversion is complete, this internal clock stops operat-
ing and the CLK pin goes to the DGND potential. Connections
for R
CLK
and C
CLK
are shown in the operating diagram of Fig-
ure 21. The nominal conversion time versus temperature for the
recommended R
CLK
and C
CLK
combination is shown in Figure
6. The internal clock provides a convenient clock source for the
AD7569/AD7669. Due to process variations, the actual operat-
ing frequency for this R
CLK
/C
CLK
combination can vary from
device to device by up to
±
25%.
Figure 6. Conversion Time vs. Temperature for Internal
Clock Operation
DIGITAL INTERFACE
DAC Timing and Control—AD7569
Table II shows the truth table for DAC operation for the
AD7569. The part contains an 8-bit DAC register, which is
loaded from the data bus under control of
CS
and
WR
. The
data contained in the DAC register determines the analog out-
put from the DAC. The
WR
input is an edge-triggered input,
and data is transferred into the DAC register on the rising edge
of
WR
. Holding
CS
and
WR
low does not make the DAC regis-
ter transparent.
Table II. AD7569 DAC Truth Table
CS
WR
RESET
DAC Function
H
L
L
g
X
H
L
g
L
X
H
H
H
H
L
DAC Register Unaffected
DAC Register Unaffected
DAC Register Updated
DAC Register Updated
DAC Register Loaded with All Zeros
L = Low State, H = High State, X = Don’t Care
The contents of the DAC register are reset to all 0s by an active
low pulse on the
RESET
line, and for the unipolar output ranges,
the output remains at 0 V after
RESET
returns high. For the bi-
polar output ranges, a low pulse on
RESET
causes the output to
go to negative full scale.
In unipolar applications, the
RESET
line
can be used to ensure power-up to 0 V on the AD7569 DAC out-
put and is also useful when used as a zero override in system cali-
bration cycles. If the
RESET
input is connected to the system
At the end of conversion, the SAR contents are transferred to
the output latch, and the SAR is reset in readiness for a new
conversion. A single conversion lasts for 8 input clock cycles.
Figure 4. Operating Waveforms Using External Clock
ANALOG INPUT
The analog input of the AD7569/AD7669 feeds into an on-chip
track-and-hold amplifier. To accommodate different full-scale
ranges, the analog input signal is conditioned by a gain/offset
network that conditions all input ranges so the internal ADC al-
ways works with a 0 V to +1.25 V signal. As a result, the input
current on the V
IN
input varies with the input range selected as
shown in Figure 5.
Figure 5. Equivalent V
IN
Circuit
TRACK-AND-HOLD
The track-and-hold (T/H) amplifier on the analog input of the
AD7569/AD7669 allows the ADC to accurately convert an in-
put sine wave of 2.5 V peak-to-peak amplitude up to a fre-
quency of 200 kHz, the Nyquist frequency of the ADC when
operated at its maximum throughput rate of 400 kHz. This
maximum rate of conversion includes conversion time and time
between conversions. Because the input bandwidth of the T/H
amplifier is much larger than 200 kHz, the input signal should
be band-limited to avoid converting high-frequency noise
components.
The operation of this T/H amplifier is essentially transparent to
the user. The T/H amplifier goes from its tracking mode to its
hold mode at the start of conversion. This occurs when the
ADC receives a conversion start command from either
ST
or
CS
&
RD
. At the end of conversion (
BUSY
going high), the
T/H reverts back to tracking the input signal.
EXTERNAL CLOCK
The AD7569/AD7669 ADC can be used with its on-chip clock
or with an externally applied clock. When using an external
clock, the CLK input of the AD7569/AD7669 may be driven
directly from 74HC, 4000B series buffers (such as 4049) or
from TTL buffers. When conversion is complete, the internal
clock is disabled. The external clock can continue to run be-
tween conversions without being disabled. The mark/space ratio
of the external clock can vary from 70/30 to 30/70.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7569KN | LC2MOS Complete, 8-Bit Analog I/0 Systems |
| AD7569KP | LC2MOS Complete, 8-Bit Analog I/0 Systems |
| AD7569TQ | LC2MOS Complete, 8-Bit Analog I/0 Systems |
| AD7669AR | LC2MOS Complete, 8-Bit Analog I/0 Systems |
| AD7569 | Complete, 8-Bit Analog I/0 Systems(完備的8位模擬I/O系統) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7569TQ | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD7572, AD7572AAR03 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| AD7572AAN03 | 制造商:Analog Devices 功能描述:ADC Single SAR 12-bit Parallel 24-Pin PDIP 制造商:Rochester Electronics LLC 功能描述:12-BIT ADC IC - Bulk |
| AD7572AAN10 | 制造商:Analog Devices 功能描述:ADC Single SAR 12-bit Parallel 24-Pin PDIP 制造商:Rochester Electronics LLC 功能描述:12-BIT ADC IC - Bulk |
| AD7572AANZ03 | 功能描述:IC ADC 12BIT HS LC2MOS 24DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。