- 您現在的位置：買賣IC網 > PDF目錄373913 > AD7679 (Analog Devices, Inc.) 18-Bit, 2.5 LSB INL, 570 kSPS SAR ADC PDF資料下載
參數資料
| 型號： | AD7679 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 18-Bit, 2.5 LSB INL, 570 kSPS SAR ADC |
| 中文描述： | 18位，2.5 LSB INL和570 kSPS的SAR型ADC |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 1186K |
| 代理商： | AD7679 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7679
TYPICAL CONNECTION DIAGRAM
Figure 25 shows a typical connection diagram for the AD7679.
Different circuitry shown on this diagram is optional and is
discussed later in this data sheet.
Analog Inputs
Figure 26 shows a simplified analog input section of the
AD7679. The diodes shown in Figure 26 provide ESD
protection for the inputs. Care must be taken to ensure that the
analog input signal never exceeds the absolute ratings on these
inputs. This will cause these diodes to become forward biased
and start conducting current. These diodes can handle a
forward-biased current of 120 mA max. This condition could
eventually occur when the input buffer’s U1 or U2 supplies are
different from AVDD. In such a case, an input buffer with a
short-circuit current limitation can be used to protect the part.
IN+
IN–
AGND
AVDD
R+ = 102
C
S
C
S
R– = 102
03085-0-028
Figure 26. Simplified Analog Input
This analog input structure is a true differential structure. By
using these differential inputs, signals common to both inputs
are rejected as shown in Figure 27, which represents typical
CMRR over frequency.
FREQUECY (kHz)
80
C
75
50
100
1000
10000
1
10
70
65
60
55
03085-0-029
Figure 27. Analog Input CMRR vs. Frequency
During the acquisition phase for ac signals, the AD7679 behaves
like a 1-pole RC filter consisting of the equivalent resistance,
R+, R–, and C
S
. Resistors R+ and R– are typically 102 and are
lumped components made up of a serial resistor and the on
resistance of the switches. C
S
is typically 60 pF and mainly
consists of the ADC sampling capacitor. This 1-pole filter with a
–3 dB cutoff frequency of 26 MHz typ reduces any undesirable
aliasing effect and limits the noise coming from the inputs.
Because the input impedance of the AD7679 is very high, the
part can be driven directly by a low impedance source without
gain error. This allows the user to put an external 1-pole RC
filter between the amplifier output and the ADC analog inputs,
as shown in Figure 25, to even further improve the noise
filtering done by the AD7679 analog input circuit. However, the
source impedance has to be kept low because it affects the ac
performance, especially the total harmonic distortion (THD).
The maximum source impedance depends on the amount of
THD that can be tolerated. The THD degrades as a function of
source impedance and the maximum input frequency, as shown
in Figure 28.
INPUT RESISTANCE (
)
–95
T
–120
45
75
105
15
–100
–105
–110
–115
20kHz
10kHz
2kHz
03085-0-030
Figure 28. THD vs. Analog Input Frequency and Source Resistance
Driver Amplifier Choice
Although the AD7679 is easy to drive, the driver amplifier
needs to meet the following requirements:
The driver amplifier and the AD7679 analog input circuit
have to be able to settle for a full-scale step of the capacitor
array at an 18-bit level (0.0004%). In the amplifier’s data
sheet, settling at 0.1% or 0.01% is more commonly
specified. This could differ significantly from the settling
time at an 18-bit level and, therefore, should be verified
prior to driver selection. The tiny op amp AD8021, which
combines ultralow noise and high gain-bandwidth, meets
this settling time requirement.
The noise generated by the driver amplifier needs to be
kept as low as possible in order to preserve the SNR and
transition noise performance of the AD7679. The noise
coming from the driver is filtered by the AD7679 analog
input circuit 1-pole low-pass filter made by R+, R–, and C
S
.
Rev. 0 | Page 17 of 28
相關PDF資料 |
PDF描述 |
|---|---|
| AD7679ACP | 18-Bit, 2.5 LSB INL, 570 kSPS SAR ADC |
| AD7679ACPRL | 18-Bit, 2.5 LSB INL, 570 kSPS SAR ADC |
| AD7679AST | 18-Bit, 2.5 LSB INL, 570 kSPS SAR ADC |
| AD7679ASTRL | 18-Bit, 2.5 LSB INL, 570 kSPS SAR ADC |
| AD7675 | 16-Bit, 100 kSPS, Differential ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7679ACP | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 18-bit Parallel/Serial 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:18BIT SAR ADC SMD 7679 LFSCP-48 |
| AD7679ACPRL | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 18-bit Parallel/Serial 48-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 570KSPS 18BIT PARALLEL/SERL 48LFCSP EP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:18-BIT,100KSPSSARADC - Tape and Reel |
| AD7679ACPZ | 功能描述:IC ADC 18BIT SAR W/BUFF 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7679ACPZRL | 功能描述:IC ADC 18BIT SAR W/BUFF 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7679AST | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 18-bit Parallel/Serial 48-Pin LQFP 制造商:Analog Devices 功能描述:18BIT SAR ADC SMD 7679 LQFP48 |
發布緊急采購，3分鐘左右您將得到回復。