- 您現在的位置：買賣IC網 > PDF目錄373953 > AD8632ARM (ANALOG DEVICES INC) 1.8 V, 5 MHz Rail-to-Rail Low Power Operational Amplifiers PDF資料下載
參數資料
| 型號： | AD8632ARM |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | 1.8 V, 5 MHz Rail-to-Rail Low Power Operational Amplifiers |
| 中文描述： | OP-AMP, 4000 uV OFFSET-MAX, 5 MHz BAND WIDTH, PDSO8 |
| 封裝： | MICRO, SOIC-8 |
| 文件頁數： | 11/12頁 |
| 文件大小： | 157K |
| 代理商： | AD8632ARM |
AD8631/AD8632
–11–
REV. 0
Table II. Snubber Network Values for Large Capacitive Loads
C
LOAD
600 pF
1 nF
10 nF
Rx
300
300
90
Cx
1 nF
1 nF
8
nF
TOTAL HARMONIC DISTORTION + NOISE
The AD863x family offers a low total harmonic distortion, which
makes this amplifier ideal for audio applications. Figure 27 shows
a graph of THD + N, which is ~0.02% @ 1 kHz, for a 1.8 V supply.
At unity gain in an inverting configuration the value of the Total
Harmonic Distortion + Noise stays consistently low over all volt-
ages supply ranges.
FREQUENCY
–
Hz
0.1
0.001
10
20k
T
–
0.01
1
10
100
1k
10k
V
S
= 1.8V
V
S
= 5V
INVERTING
A
V
= 1
Figure 27. THD + N vs. Frequency Graph
AD8632 Turn-On Time
The low voltage, low power AD8632 features an extraordinary turn
on time. This is about 500 ns for V
SY
= 5 V, which is impressive
considering the low supply current (300
μ
A typical per amplifier).
Figure 28 shows a scope picture of the AD8632 with both channels
configured as followers. Channel A has an input signal of 2.5 V and
channel B has the input signal at ground. The top waveform shows
the supply voltage and the bottom waveform reflects the response
of the amplifier at the output of Channel A.
TIME
–
200ns/DIV
0
0
0
V
–
0
0
0
0
V
S
= 5V
A
V
= 1
V
IN
= 2.5V STEP
0V
0V
Figure 28. AD8632 Turn-On Time
A MICROPOWER REFERENCE VOLTAGE GENERATOR
Many single-supply circuits are configured with the circuit biased
to one-half of the supply voltage. In these cases, a false-ground
reference can be created by using a voltage divider buffered by an
amplifier. Figure 28 shows the schematic for such a circuit.
The two 1 M
resistors generate the reference voltages while
drawing only 0.9
μ
A of current from a 1.8 V supply. A capacitor
connected from the inverting terminal to the output of the op
amp provides compensation to allow a bypass capacitor to be
connected at the reference output. This bypass capacitor helps
establish an ac ground for the reference output.
AD8631
10k
0.022 F
V
0.9V TO 2.5V
1 F
1 F
1M
1.8V TO 5V
100
1M
Figure 29. A Micropower Reference Voltage Generator
MICROPHONE PREAMPLIFIER
The AD8631 is ideal to use as a microphone preamplifier.
Figure 30 shows this implementation.
AD8631
V
OUT
R3
220k
1.8V
V
REF
= 0.9V
R2
22k
C1
0.1 F
1.8V
R1
2.2k
ELECTRET
MIC
A
V
=R2
V
IN
Figure 30. A Microphone Preamplifier
R1 is used to bias an electret microphone and C1 blocks dc voltage
from the amplifier. The magnitude of the gain of the amplifier is
approximately R3/R2 when R2
≥
10
R1. V
REF
should be equal to
1/2
1.8 V for maximum voltage swing.
Direct Access Arrangement for Telephone Line Interface
Figure 31 illustrates a 1.8 V transmit/receive telephone line interface
for 600
transmission systems. It allows full duplex transmission of
signals on a transformer-coupled 600
line in a differential manner.
Amplifier A1 provides gain that can be adjusted to meet the modem
output drive requirements. Both A1 and A2 are configured to apply
the largest possible signal on a single supply to the transformer.
Amplifier A3 is configured as a difference amplifier for two reasons:
(1) It prevents the transmit signal from interfering with the receive
signal and (2) it extracts the receive signal from the transmission line
for amplification by A4. A4’s gain can be adjusted in the same
manner as A1’s to meet the modem’s input signal requirements.
Standard resistor values permit the use of SIP (Single In-line
Package) format resistor arrays. Couple this with the AD8631/
相關PDF資料 |
PDF描述 |
|---|---|
| AD8638 | 16V Auto-Zero, Rail-to-Rail Output, Precision Amplifiers |
| AD8638ARJZ | 16V Auto-Zero, Rail-to-Rail Output, Precision Amplifiers |
| AD8638ARZ | 16V Auto-Zero, Rail-to-Rail Output, Precision Amplifiers |
| AD8641ARZ-REEL7 | Low Power, Rail-to-Rail Output Precision JFET Amplifier |
| AD8641ARZ1 | Low Power, Rail-to-Rail Output Precision JFET Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8632ARM-R2 | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R I/O 6V 8-Pin MSOP T/R 制造商:Rochester Electronics LLC 功能描述:DUAL, LOW VOLTAGE AMPLIFIER - Bulk |
| AD8632ARM-REEL | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R I/O 6V 8-Pin MSOP T/R 制造商:Rochester Electronics LLC 功能描述:DUAL, LOW VOLTAGE AMPLIFIER - Tape and Reel |
| AD8632ARMZ-R2 | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R I/O 6V 8-Pin MSOP T/R 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD8632ARMZ-REEL | 功能描述:IC OPAMP GP R-R 5MHZ DUAL 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD8632AR-REEL | 制造商:Analog Devices 功能描述:OP Amp Dual GP R-R I/O 6V 8-Pin SOIC N T/R |
發布緊急采購，3分鐘左右您將得到回復。