- 您現在的位置：買賣IC網 > Datasheet目錄38 > ADM1073ARU-REEL (Analog Devices Inc)IC CTRLR HOTSWAP -48V 14TSSOP Datasheet資料下載
參數資料
| 型號： | ADM1073ARU-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/24頁 |
| 文件大小： | 370K |
| 描述： | IC CTRLR HOTSWAP -48V 14TSSOP |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | -35 V ~ -80 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
| 配用： | EVAL-ADM1073MEBZ-ND - BOARD EVALUATION FOR ADM1073 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
Data Sheet
ADM1073
Rev. B | Page 15 of 24
SENSE
The SENSE pin is used for sensing the voltage across an
external power sense resistor. This voltage is differentially
measured with respect to VEE, and used to control the GATE.
If SENSE is lower than 100 mV (after the soft start time), the
GATE pin is allowed to increase up to 12 V to provide
maximum FET enhancement. If the current increases such that
the SENSE pin tries to go above 100 mV, the GATE pin is
controlled in a feedback loop to ensure that the voltage across
the sense resistor is regulated at exactly 100 mV.
SENSE RESISTOR
The ADM1073s current limiting function can operate at
different current levels. The current limit is determined by
selection of the sense resistor, R
SENSE
. Table 4 shows how the
maximum allowable load current (I
LOAD(MAX)
) and the minimum
and maximum inrush currents (ILIMIT(MIN) and ILIMIT(MAX)) are
related to the value of RSENSE.
Table 4. Minumum and Maximum Inrush Current and Load
Current Levels for Different Values of R
SENSE
RSENSE (m&)
ILOAD(MAX) (A) ILIMIT(MIN) (A) ILIMIT(MAX) (A)
5
17.20
19.40
20.60
10
8.60
9.70
10.30
15
5.73
6.47
6.87
18
4.78
5.39
5.72
22
3.91
4.41
4.68
33
2.61
2.94
3.12
47
1.83
2.06
2.19
51
1.69
1.90
2.02
68
1.26
1.43
1.51
75
1.15
1.29
1.37
90
0.96
1.08
1.14
SOFT START (SS PIN)
The SS pin is used to determine the inrush current profile.
A capacitor should be attached to this pin. Whenever the FET
is requested to turn on, the SS pin is held at ground until the
SENSE pin reaches a few mV. A current source is then turned
on, which linearly ramps the capacitor up to 2.5 V. The
reference voltage for the GATE linear control amplifier is
derived from the soft start voltage, such that the inrush linear
current limit is defined as
SENSE
START
SOFT
LIMIT
R
V
?/DIV>
=
20
/
_
Overdriving the SS Pin
The SS pin can be overdriven externally from 0.360 V to 1.95 V
to offset the current limit control loop threshold from 18 mV to
100 mV. This allows different current limits to be selected at
different points of operation without using multiple sense
resistors. The current limit voltage is clamped at 100 mV
maximum.
GATE
Analog output for driving the external FET gate. This pin is
switched to V
EE
when the FET is off, is linearly controlled when
the FET is at the programmed inrush current limit, and is
switched to VIN when the FET is fully enhanced. The source
current capability is small to provide slow controlled turn-on,
and the sink current capability is large to provide fast turn-off.
V
IN
Positive supply pin. This current-driven supply is shunt-
regulated at 12.3 V internally, and should be connected to the
most positive input supply terminal (usually 48 V RTN or 0 V)
through a dropper resistor. The resistor should be chosen such
that it always supplies enough current to overcome the
maximum quiescent supply current of the chip. Default R
DROP
=
30 k&.
V
EE
Negative supply input. This pin should be connected directly to
the most negative input supply terminal (48 V). This pin is
also used for differentially sensing across the external power
resistor, and should, therefore, be connected as close to the
sense resistor as possible. (See the Kelvin Sense Resistor
Connection section.)
TIMING CONTROLTIMER
The TIMER pin is an analog pin that determines the maximum
on-time when the FET is in linear current limit, and controls
the PWM duty cycle for pulsed load capacitor charging. A
capacitor should be attached to this pin. When the FET is in
current limit, a 19 礎 current source charges the external
capacitor. If the FET is still in current limit when the TIMER
capacitor reaches 2.5 V, the GATE driver is turned off and a
1 礎 discharge current sink is turned on. The GATE remains
low until the TIMER capacitor is reduced to 0.5 V. At this point,
the GATE pin is turned on again. If the FET goes back into
current limit, the TIMER recharging starts again.
The PWM duty cycle is set at 6% default level by the size of
these two current sources. Adding a resistor from TIMER to V
EE
decreases the duty cycle. Adding a resistor from TIMER to V
IN
increases the duty cycle.
In addition, a current proportional to the current into the
DRAIN pin is added to the charging current. The additional
current varies linearly with DRAIN voltage. This reduces the
maximum on-time and the percentage PWM duty cycle when
there is a large voltage across the FET.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM4210-2AUJZ-RL7 | IC CTLR HOTSWAP LV TSOT23-6 |
| ADVFC32SH | IC CONV V/F F/V MONO TO100-10 |
| FAN4800ASNY | IC CTLR COMBO PFC/PWM 16-DIP |
| FAN4800AUN | IC PWM/PFC CTLR COMBO 16-MDIP |
| FAN4800CUN | IC PWM/PFC CTLR COMBO 16-MDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1073ARU-REEL7 | 制造商:Analog Devices 功能描述:Hot Swap Controller 1-CH -80V 14-Pin TSSOP T/R 制造商:Analog Devices 功能描述:FULL FEATURED -48V HOT SWAP CTRL'R I.C. - Tape and Reel |
| ADM1073ARUZ | 功能描述:IC HOTSWAP CTRLR -48V 14-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| ADM1073ARUZ-REEL | 功能描述:IC CTRLR HOTSWAP -48V 14TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| ADM1073ARUZ-REEL7 | 功能描述:IC CTRLR HOTSWAP -48V 14TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| ADM1073BRUZ | 功能描述:IC CTRLR HOTSWAP -48V 14TSSOP 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。