- 您現在的位置：買賣IC網 > PDF目錄375730 > FAN8741 (Fairchild Semiconductor Corporation) Spindle Motor and 6-CH Driver PDF資料下載
參數資料
| 型號： | FAN8741 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Spindle Motor and 6-CH Driver |
| 中文描述： | 主軸電機和6通道驅動器 |
| 文件頁數： | 14/23頁 |
| 文件大小： | 541K |
| 代理商： | FAN8741 |
14
www.fairchildsemi.com
FAN8741/FAN8742 Rev. 1.0.1
F
2. Torque Control & Output Current Control Of Sled Motor(2-phase Step Motor)
1) By amplifying the voltage difference between V
REF
and SLIN1(or SLIN2) from Servo IC(or DSP), the Torque AMP produces
the input voltage(V
AMP
) which means input current command.
2) The output current (I
O
) is converted into the voltage (V
CS
) through the sense resistor (R
CS
) and compared with the V
AMP
.
3) The clock generator always make the RS latch become set periodically, this enables the output driver’s on state, when the V
CS
and the V
AMP
are equal the state becomes off.
4) By the negative feedback loop, the sensed output voltage V
CS
equals to the V
AMP
.
5) To avoid output upper and lower transistor’s short through, a switch trick is needed. Turn on delay time is 1usec, so the phase
delay time,when changing the current direction, is 1usec.
6) The gain and limit currents are calculated as shown in the table below.(Gvo=V
AMP
/[SLIN1(or SLIN2)-V
REF
]=1[V/V]
7)
The range of the torque voltage is as shown below when Rcs=1W, R
EXT1
=0
.
Torque limit current
Input/Output gain[A/V]
RE X T 1
Remark
is gain scaler
Torque AMP
SLIN1
(or SLIN2)
Driver
M
Rcs
Vcs
+
-
Io
VM2
V
AMP
+
-
LPF
R
S
Q
Clock
Generator
Drive Logic
Inside IC
I
OMAX
4
V
REF
R
EXT1
10K
10K
Rcs
----------
+
-------------------------------------------
-------------
RE X T 1
+
-------------------------------------------
Forward
Dead
zone-
Reverse
[A]
0
SLIN1(or SLIN2)-V
REF
0.5
15mV
-15mV
G
MSL
=G
VO
/ R
CS
Dead
相關PDF資料 |
PDF描述 |
|---|---|
| FAN8741G | Spindle Motor and 6-CH Driver |
| FAN8741GX | Spindle Motor and 6-CH Driver |
| FAN8741MTF | Spindle Motor and 6-CH Driver |
| FAN8741MTFX | Spindle Motor and 6-CH Driver |
| FAN8742G | Spindle Motor and 6-CH Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN8741G | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Spindle Motor and 6-CH Driver |
| FAN8741GX | 功能描述:馬達/運動/點火控制器和驅動器 POWER_CONVERSION RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| FAN8741MTF | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Spindle Motor and 6-CH Driver |
| FAN8741MTFX | 功能描述:IC PWM SPINDLE 6CH DRIVE 56TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 產品變化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 標準包裝:1 系列:- 應用:DC 電機控制器，無刷（BLDC），3 相 評估套件:可供 輸出數:1 電流 - 輸出:100mA 電壓 - 負載:5.25 V ~ 20 V 電源電壓:5.25 V ~ 20 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-VQFN（7x7） 包裝:剪切帶 (CT) 其它名稱:ATA6833-PLQWCT |
| FAN8742G | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Spindle Motor and 6-CH Driver |
發布緊急采購，3分鐘左右您將得到回復。