- 您現在的位置：買賣IC網 > PDF目錄22053 > KMC8113TMP3600V (Freescale Semiconductor)IC DSP 300/400MHZ 431FCPGA PDF資料下載
參數資料
| 型號： | KMC8113TMP3600V |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 33/44頁 |
| 文件大小： | 0K |
| 描述： | IC DSP 300/400MHZ 431FCPGA |
| 標準包裝： | 2 |
| 系列： | StarCore |
| 類型： | SC140 內核 |
| 接口： | 以太網，I²C，TDM，UART |
| 時鐘速率： | 300MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 1.436MB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.10V |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 431-BFBGA，F(xiàn)CBGA |
| 供應商設備封裝： | 431-FCPBGA（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Hardware Design Considerations
MSC8113 Tri-Core Digital Signal Processor Data Sheet, Rev. 1
Freescale Semiconductor
39
Each VCC and VDD pin on the MSC8113 device should have a low-impedance path to the board power supply. Similarly, each
GND
pin should have a low-impedance path to the ground plane. The power supply pins drive distinct groups of logic on the
chip. The VCC power supply should have at least four 0.1 F by-pass capacitors to ground located as closely as possible to the
four sides of the package. The capacitor leads and associated printed circuit traces connecting to chip VCC, VDD, and GND should
be kept to less than half an inch per capacitor lead. A four-layer board is recommended, employing two inner layers as VCC and
GND
planes.
All output pins on the MSC8113 have fast rise and fall times. PCB trace interconnection length should be minimized to
minimize undershoot and reflections caused by these fast output switching times. This recommendation particularly applies to
the address and data buses. Maximum PCB trace lengths of six inches are recommended. For the DSI control signals in
synchronous mode, ensure that the layout supports the DSI AC timing requirements and minimizes any signal crosstalk.
Capacitance calculations should consider all device loads as well as parasitic capacitances due to the PCB traces. Attention to
proper PCB layout and bypassing becomes especially critical in systems with higher capacitive loads because these loads create
higher transient currents in the VCC, VDD, and GND circuits. Pull up all unused inputs or signals that will be inputs during reset.
Special care should be taken to minimize the noise levels on the PLL supply pins. There is one pair of PLL supply pins:
VCCSYN-GNDSYN. To ensure internal clock stability, filter the power to the VCCSYN input with a circuit similar to the one in
Figure 34. For optimal noise filtering, place the circuit as close as possible to VCCSYN. The 0.01-F capacitor should be closest
to VCCSYN, followed by the 10-F capacitor, the 10-nH inductor, and finally the 10-Ω resistor to VDD. These traces should be
kept short and direct. Provide an extremely low impedance path to the ground plane for GNDSYN. Bypass GNDSYN to VCCSYN
by a 0.01-F capacitor located as close as possible to the chip package. For best results, place this capacitor on the backside of
the PCB aligned with the depopulated void on the MSC8113 located in the square defined by positions, L11, L12, L13, M11,
M12, M13, N11, N12, and N13.
3.3
Connectivity Guidelines
Unused output pins can be disconnected, and unused input pins should be connected to the non-active value, via resistors to
VDDH or GND, except for the following:
If the DSI is unused (DDR[DSIDIS] is set), HCS and HBCS must pulled up and all the rest of the DSI signals can be
disconnected.
When the DSI uses synchronous mode, HTA must be pulled up. In asynchronous mode, HTA should be pulled either
up or down, depending on design requirements.
HDST
can be disconnected if the DSI is in big-endian mode, or if the DSI is in little-endian mode and the
DCR[DSRFA] bit is set.
When the DSI is in 64-bit data bus mode and DCR[BEM] is cleared, pull up HWBS[1–3]/HDBS[1–3]/HWBE[1–3]/
HDBE[1–3]
and HWBS[4–7]/HDBS[4–7]/HWBE[4–7]/HDBE[4–7]/PWE[4–7]/PSDDQM[4–7]/PBS[4–7].
When the DSI is in 32-bit data bus mode and DCR[BEM] is cleared, HWBS[1–3]/HDBS[1–3]/HWBE[1–3]/HDBE[1–3]
must be pulled up.
When the DSI is in asynchronous mode, HBRST and HCLKIN should either be disconnected or pulled up.
The following signals must be pulled up: HRESET, SRESET, ARTRY, TA, TEA, PSDVAL, and AACK.
In single-master mode (BCR[EBM] = 0) with internal arbitration (PPC_ACR[EARB] = 0):
— BG, DBG, and TS can be left unconnected.
— EXT_BG[2–3], EXT_DBG[2–3], and GBL can be left unconnected if they are multiplexed to the system bus
functionality. For any other functionality, connect the signal lines based on the multiplexed functionality.
— BR must be pulled up.
— EXT_BR[2–3] must be pulled up if multiplexed to the system bus functionality.
Figure 34. VCCSYN Bypass
VDD
0.01 F
10 F
VCCSYN
10
Ω
10nH
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2W2-CW-F1 | CONVERTER MOD DC/DC 15V 100W |
| 10018784-11112TLF | CONN PCI EXPRESS 98POS VERT PCB |
| 10018784-11102TLF | CONN PCI EXPRESS 98POS VERT PCB |
| AMC22DRXI | CONN EDGECARD 44POS .100 DIP SLD |
| VE-2WR-CW-F4 | CONVERTER MOD DC/DC 7.5V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KMC8113TMP4800V | 功能描述:IC DSP 300/400MHZ 431FCPGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| KMC8113TVT3600V | 功能描述:IC DSP 300/400MHZ 431FCPGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| KMC8113TVT4800V | 功能描述:IC DSP 300/400MHZ 431FCPGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| KMC811E2CFN2 | 制造商:Freescale Semiconductor 功能描述:MCU - Bulk |
| KMC811E2CP2 | 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。