- 您現在的位置：買賣IC網 > Datasheet目錄46 > SG6961SY (Fairchild Semiconductor)IC PFC CTRLR AVERAGE CURR 8SOIC Datasheet資料下載
參數資料
| 型號： | SG6961SY |
| 廠商： | Fairchild Semiconductor |
| 文件頁數： | 10/14頁 |
| 文件大小： | 835K |
| 描述： | IC PFC CTRLR AVERAGE CURR 8SOIC |
| 標準包裝： | 2,500 |
| 模式： | 平均電流 |
| 頻率 - 開關： | 50kHz |
| 電流 - 啟動： | 10µA |
| 電源電壓： | 12 V ~ 20 V |
| 工作溫度： | -20°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOICN |
| 包裝： | 帶卷 (TR) |
?2008 Fairchild Semiconductor Corporation
www.fairchildsemi.com
SG6961 " Rev. 1.3.2
10
Functional Description
Error Amplifier
The inverting input of the error amplifier is referenced to
INV. The output of the error amplifier is referenced to
COMP. The non-inverting input is internally connected
to a fixed 2.5V ?2% voltage. The output of the error
amplifier is used to determine the on-time of the PWM
output and regulate the output voltage. To achieve a
low input current THD, the variation of the on time
within one input AC cycle should be very small. A multi-
vector error amplifier is built in to provide fast transient
response and precise output voltage clamping.
For SG6961, connecting a capacitance, such as 1礔,
between COMP and GND is suggested. The error
amplifier is a trans-conductance amplifier that converts
voltage to current with a 125祄ho.
Startup Current
Typical startup current is less than 20礎. This ultra-low
startup current allows the usage of high resistance,
low-wattage startup resistor. For example, 1 M&/0.25W
startup resistor and a 10礔/25V (V
CC
hold-up) capacitor
are recommended for an AC-to-DC power adaptor with
a wide input range 85 to 265V
AC
.
Operating Current
Operating current is typically 4.5mA. The low operating
current enables a better efficiency and reduces the
requirement of V
CC
hold-up capacitance.
Maximum On-Time Operation
Given a fixed inductor value and maximum output
power, the relationship between on-time and line
voltage is:
?/DIV>
"
"
"
=
2
rms
O
ON
V
P
L
2
t
(1)
If the line voltage is too low or the inductor value is too
high, t
ON
is too long. To avoid extra low operating
frequency and achieve brownout protection, the
maximum value of t
ON
is programmable by one resistor,
R
I
, connected between MOT and GND. A 24k& resistor
R
I
generates corresponds to 25祍 maximum on time:
( )
礢
24
25
)
k
(
R
t
I
ONMAX
"
?/DIV>
=
(2)
The range of the maximum on-time is designed as 10 ~
50祍.
Peak Current Limiting
The switch current is sensed by one resistor. The
signal is feed into CS pin and an input terminal of a
comparator. A high voltage in CS pin terminates a
switching cycle immediately and cycle-by-cycle current
limit is achieved. The designed threshold of the
protection point is 0.82V.
Leading-Edge Blanking (LEB)
A turn-on spike on CS pin appears when the power
MOSFET is switched on. At the beginning of each
switching pulse, the current-limit comparator is disabled
for around 400ns to avoid premature termination. The
gate drive output cannot be switched off during the
blanking period. Conventional RC filtering is not
necessary, so the propagation delay of current limit
protection can be minimized.
Under-Voltage Lockout (UVLO)
The turn-on and turn-off threshold voltage is fixed
internally at 12V/9.5V. This hysteresis behavior
guarantees a one-shot startup with proper startup
resistor and hold-up capacitor. With an ultra-low startup
current of 20礎, one 1M& R
IN
is sufficient for startup
under low input line voltage, 85V
rms
. Power dissipation
on R
IN
would be less than 0.1W even under high line
(V
AC
=265V
rms
) condition.
Output Driver
With low on resistance and high current driving
capability, the output driver can drive an external
capacitive load larger than 3000pF. Cross conduction
current has been avoided to minimize heat dissipation,
improving efficiency and reliability. This output driver is
internally clamped by a 16.5V Zener diode.
Zero-Current Detection (ZCD)
The zero-current detection of the inductor is achieved
using its auxiliary winding. When the stored energy of
the inductor is fully released to output, the voltage on
ZCD goes down and a new switching cycle is enabled
after a ZCD trigger. The power MOSFET is always
turned on with zero inductor current such that turn-on
loss and noise can be minimized. The converter works
in boundary mode and peak inductor current is always
exactly twice of the average current. A natural power
factor correction function is achieved with the low-
bandwidth, on-time modulation. An inherent maximum
off time is built in to ensure proper startup operation.
This ZCD pin can be used as a synchronous input.
Noise Immunity
Noise on the current sense or control signal can cause
significant pulse-width jitter, particularly in the
boundary-mode operation. Slope compensation and
built-in debounce circuit can alleviate this problem.
Because the SG6961 has a single ground pin, high sink
current at the output cannot be returned separately.
Good high-frequency or RF layout practices should be
followed. Avoiding long PCB traces and component
leads, locating compensation and filter components
near to the FAN6961, and increasing the power
MOSFET gate resistance improve performance.
相關PDF資料 |
PDF描述 |
|---|---|
| SI3500-A-GM | IC POE SWITCH PWR OVER LAN 20QFN |
| SI786LSG-E3 | IC REG QD BUCK/LINEAR 28SSOP |
| SIC417CD-T1-E3 | IC REG DL BCK/LINEAR SYNC 32MLPQ |
| SP619EK-L/TR | IC HIGH CURRENT SW SOT23-6 |
| TC573302ECTTR | IC REG CTRLR SGL 3.3V SOT23A-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SG6961SZ | 功能描述:功率因數校正 IC Power Factor Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| SG6980 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Single-Stage PFC Controller |
| SG6980DDZ | 功能描述:開關變換器、穩壓器與控制器 Single Stage PFC Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SG6980DZ | 功能描述:開關變換器、穩壓器與控制器 Single Stage PFC Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SG6980SZ | 功能描述:開關變換器、穩壓器與控制器 Single Stage PFC RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。