- 您現在的位置：買賣IC網 > PDF目錄382682 > TPS75115QPWPREPR (Texas Instruments, Inc.) FAST-TRANSIENT-RESPONSE 1.5-A LOW-DROPOUT VOLTAGE REGULATORS PDF資料下載
參數資料
| 型號： | TPS75115QPWPREPR |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | FAST-TRANSIENT-RESPONSE 1.5-A LOW-DROPOUT VOLTAGE REGULATORS |
| 中文描述： | 快速瞬態響應1.5低壓差電壓調節器 |
| 文件頁數： | 15/27頁 |
| 文件大小： | 398K |
| 代理商： | TPS75115QPWPREPR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
TPS75101-Q1,
’
75115-Q1,
’
75118-Q1,
’
75125-Q1,
’
75133-Q1 WITH POWER GOOD
TPS75301-Q1, TPS75315-Q1, TPS75318-Q1, TPS75325-Q1, TPS75333-Q1 WITH RESET
FAST-TRANSIENT-RESPONSE 1.5-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS159
–
APRIL 2003
15
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
The TPS751xxQ or TPS753xxQ family includes four fixed-output voltage regulators (1.5 V, 1.8 V, 2.5 V and 3.3 V),
and an adjustable regulator, the TPS75x01Q (adjustable from 1.5 V to 5 V).
minimum load requirements
The TPS751xxQ and TPS753xxQ families are stable even at no load; no minimum load is required for operation.
pin functions
enable (EN)
The EN terminal is an input which enables or shuts down the device. If EN is a logic high, the device will be in
shutdown mode. When EN goes to logic low, then the device will be enabled.
power-good (PG) (TPS751xxQ)
The PG terminal is an open drain, active high output that indicates the status of V
O
(output of the LDO). When V
O
reaches 83% of the regulated voltage, PG will go to a high impedance state. It will go to a low-impedance state when
V
O
falls below 83% (i.e. over load condition) of the regulated voltage. The open drain output of the PG terminal
requires a pullup resistor
.
sense (SENSE)
The SENSE terminal of the fixed-output options must be connected to the regulator output, and the connection
should be as short as possible. Internally, SENSE connects to a high-impedance wide-bandwidth amplifier through
a resistor-divider network and noise pickup feeds through to the regulator output. It is essential to route the SENSE
connection in such a way to minimize/avoid noise pickup. Adding RC networks between the SENSE terminal and
V
O
to filter noise is not recommended because it may cause the regulator to oscillate.
feedback (FB)
FB is an input terminal used for the adjustable-output options and must be connected to an external feedback
resistor divider. The FB connection should be as short as possible. It is essential to route it in such a way to
minimize/avoid noise pickup. Adding RC networks between FB terminal and V
O
to filter noise is not recommended
because it may cause the regulator to oscillate.
reset (RESET) (TPS753xxQ)
The RESET terminal is an open drain, active low output that indicates the status of V
O
. When V
O
reaches 95% of
the regulated voltage, RESET will go to a low-impedance state after a 100-ms delay. RESET will go to a
high-impedance state when V
O
is below 95% of the regulated voltage. The open-drain output of the RESET terminal
requires a pullup resistor.
GND/HEATSINK
All GND/HEATSINK terminals are connected directly to the mount pad for thermal-enhanced operation. These
terminals could be connected to GND or left floating.
input capacitor
For a typical application, an input bypass capacitor (0.22
μ
F
–
1
μ
F) is recommended for device stability. This
capacitor should be as close to the input pins as possible. For fast transient condition where droop at the input of
the LDO may occur due to high inrush current, it is recommended to place a larger capacitor at the input as well.
The size of this capacitor is dependant on the output current and response time of the main power supply, as well
as the distance to the load (LDO).
相關PDF資料 |
PDF描述 |
|---|---|
| TPS75101QPWPREPR | FAST-TRANSIENT-RESPONSE 1.5-A LOW-DROPOUT VOLTAGE REGULATORS |
| TPS75133QPWPRQ1 | CB 2C 2#0 PIN RECP WALL |
| TPS75125QPWPRQ1 | FAST-TRANSIENT-RESPONSE 1.5-A LOW-DROPOUT VOLTAGE REGULATORS |
| TPS75633KTTR | FAST-TRANSIENT RESPONSE 5-A LOW-DROPOUT VOLTAGE REGULATORS |
| TPS75615KTTR | FAST-TRANSIENT RESPONSE 5-A LOW-DROPOUT VOLTAGE REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS75115QPWPRG4 | 功能描述:低壓差穩壓器 - LDO Fast-Tran-Resp 1.5-A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS75118QPWP | 功能描述:低壓差穩壓器 - LDO Fast-Tran-Resp 1.5-A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS75118QPWPG4 | 功能描述:低壓差穩壓器 - LDO Fast-Tran-Resp 1.5-A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS75118QPWPR | 功能描述:低壓差穩壓器 - LDO Fast-Tran-Resp 1.5-A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS75118QPWPRG4 | 功能描述:低壓差穩壓器 - LDO Fast-Tran-Resp 1.5-A RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。