- 您現在的位置：買賣IC網 > PDF目錄363878 > W29C020T-70A (WINBOND ELECTRONICS CORP) BOX 3.4X2.56X1.02 W/6 BTNS ALMOND PDF資料下載
參數資料
| 型號： | W29C020T-70A |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | BOX 3.4X2.56X1.02 W/6 BTNS ALMOND |
| 中文描述： | 256K X 8 FLASH 5V PROM, 70 ns, PDSO32 |
| 封裝： | TSOP1-32 |
| 文件頁數： | 4/21頁 |
| 文件大小： | 267K |
| 代理商： | W29C020T-70A |
W29C020
- 4 -
will remain enabled unless the disable commands are issued. A power transition will not reset the
software data protection feature. To reset the device to unprotected mode, a six-byte command
sequence is required. For information about specific codes, see the Command Codes for Software
Data Protection in the Table of Operating Modes. For information about timing waveforms, see the
timing diagrams below.
Hardware Data Protection
The integrity of the data stored in the W29C020 is also hardware protected in the following ways:
(1) Noise/Glitch Protection: A WE pulse of less than 15 nS in duration will not initiate a write cycle.
(2) V
DD
Power Up/Down Detection: The write operation is inhibited when V
DD
is less than 2.5V.
(3) Write Inhibit Mode: Forcing
OE
low, CE high, or WE high will inhibit the write operation. This
prevents inadvertent writes during power-up or power-down periods.
(4) V
DD
power-on delay: When V
DD
reaches its sense level, the device will automatically timeout for
5 mS before any write (erase/program) operation.
Chip Erase Modes
The entire device can be erased by using a six-byte software command code. See the Software Chip
Erase Timing Diagram.
Boot Block Operation
There are two boot blocks (8K bytes each) in this device, which can be used to store boot code. One
of them is located in the first 8K bytes and the other is located in the last 8K bytes of the memory.
The first 8K or last 8K of the memory can be set as a boot block by using a seven-byte command
sequence.
See Command Codes for Boot Block Lockout Enable for the specific code. Once this feature is set
the data for the designated block cannot be erased or programmed (programming lockout); other
memory locations can be changed by the regular programming method. Once the boot block
programming lockout feature is activated, the chip erase function will be disabled. In order to detect
whether the boot block feature is set on the two 8K blocks, users can perform a six-byte command
sequence: enter the product identification mode (see Command Codes for Identification/Boot Block
Lockout Detection for specific code), and then read from address "00002 hex" (for the first 8K bytes)
or "3FFF2 hex" (for the last 8K bytes). If the output data is "FF hex," the boot block programming
lockout feature is activated; if the output data is "FE hex," the lockout feature is deactivated and the
block can be programmed.
To return to normal operation, perform a three-byte command sequence to exit the identification
mode. For the specific code, see Command Codes for Identification/Boot Block Lockout Detection.
Data Polling (DQ7)- Write Status Detection
The W29C020 includes a data polling feature to indicate the end of a write cycle. When the
W29C020 is in the internal write cycle, any attempt to read DQ7 from the last byte loaded during the
page/byte-load cycle will receive the complement of the true data. Once the write cycle is completed.
DQ7 will show the true data. See the DATA Polling Timing Diagram.
相關PDF資料 |
PDF描述 |
|---|---|
| W29C020T-70B | BOX 3.4X2.56X1.02 W/6 BTNS BLK |
| W29C020T-90A | BOX 2.53X1.73X.65 W/2 BTNS BLK |
| W29C020T-90B | 256K X 8 CMOS FLASH MEMORY |
| W29C020P-70 | BOX 3.4X2.56X1.02 W/3 BTNS ALMOND |
| W29C020P-70A | 256K X 8 CMOS FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W29C020T-70B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY |
| W29C020T-90 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY |
| W29C020T-90A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY |
| W29C020T-90B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K X 8 CMOS FLASH MEMORY |
| W29C022 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256K x 8 CMOS FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。