- 您現在的位置：買賣IC網 > PDF目錄363882 > W39L040Q-90B (WINBOND ELECTRONICS CORP) 512 K X 8 CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | W39L040Q-90B |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 512 K X 8 CMOS FLASH MEMORY |
| 中文描述： | 512K X 8 FLASH 3.3V PROM, 90 ns, PDSO32 |
| 封裝： | 8 X 14 MM, STSOP-32 |
| 文件頁數： | 7/27頁 |
| 文件大小： | 334K |
| 代理商： | W39L040Q-90B |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
W39L040
Publication Release Date: February 10, 2003
- 7 -
Revision A3
Write Operation Status
DQ7: Data Polling
The W39L040 device features Data Polling as a method to indicate to the host that the embedded
algorithms are in progress or completed.
During the Embedded Program Algorithm, an attempt to read the device will produce the complement
of the data last written to DQ7. Upon completion of the Embedded Program Algorithm, an attempt to
read the device will produce the true data last written to DQ7.
During the Embedded Erase Algorithm, an attempt to read the device will produce a "0" at the DQ7
output. Upon completion of the Embedded Erase Algorithm, an attempt to read the device will produce
a "1" at the DQ7 output.
For chip erase, the Data Polling is valid after the rising edge of the sixth pulse in the six #WE write
pulse sequences. For sector erase, the Data Polling is valid after the last rising edge of the sector
erase #WE pulse. Data Polling must be performed at sector addresses within any of the sectors being
erased. Otherwise, the status may not be valid.
Just prior to the completion of Embedded Algorithm operations DQ7 may change asynchronously
while the output enable (#OE) is asserted low. This means that the device is driving status information
on DQ7 at one instant of time and then that byte
′
s valid data at the next instant of time. Depending on
when the system samples the DQ7 output, it may read the status or valid data. Even if the device has
completed the Embedded Algorithm operations and DQ7 has a valid data, the data outputs on DQ0 –
DQ6 may be still invalid. The valid data on DQ0
DQ7 will be read on the successive read attempts.
The Data Polling feature is only active during the Embedded Programming Algorithm, Embedded
Erase Algorithm, or sector erase time-out (see "Command Definitions").
DQ6: Toggle Bit
The W39L040 also features the "Toggle Bit" as a method to indicate to the host system that the
embedded algorithms are in progress or completed.
During an Embedded Program or Erase Algorithm cycle, successive attempts to read (#OE toggling)
data from the device at any address will result in DQ6 toggling between one and zero. Once the
Embedded Program or Erase Algorithm cycle is completed, DQ6 will stop toggling and valid data will
be read on the next successive attempt. During programming, the Toggle Bit is valid after the rising
edge of the fourth #WE pulse in the four write pulse sequence. For chip erase, the Toggle Bit is valid
after the rising edge of the sixth #WE pulse in the six write pulse sequence. For sector/page erase, the
Toggle Bit is valid after the last rising edge of the sector/page erase #WE pulse. The Toggle Bit is
active during the sector/page erase time-out.
Either #CE or #OE toggling will cause DQ6 to toggle.
相關PDF資料 |
PDF描述 |
|---|---|
| W39L040Q-90J | 512 K X 8 CMOS FLASH MEMORY |
| W39L040Q-90K | 512 K X 8 CMOS FLASH MEMORY |
| W39L040T-70 | 512 K X 8 CMOS FLASH MEMORY |
| W39L040T-70B | 512 K X 8 CMOS FLASH MEMORY |
| W39L040T-70J | 512 K X 8 CMOS FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W39L040Q-90J | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512 K X 8 CMOS FLASH MEMORY |
| W39L040Q-90K | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512 K X 8 CMOS FLASH MEMORY |
| W39L040T-70 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512 K X 8 CMOS FLASH MEMORY |
| W39L040T-70B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512 K X 8 CMOS FLASH MEMORY |
| W39L040T-70J | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512 K X 8 CMOS FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。