- 您現在的位置：買賣IC網 > PDF目錄363882 > W39V040BPZ (WINBOND ELECTRONICS CORP) W39V040B PDF資料下載
參數資料
| 型號： | W39V040BPZ |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | W39V040B |
| 中文描述： | 512K X 8 FLASH 3.3V PROM, 11 ns, PQCC32 |
| 封裝： | LEAD FREE, PLASTIC, LCC-32 |
| 文件頁數： | 8/32頁 |
| 文件大小： | 356K |
| 代理商： | W39V040BPZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
W39V040B
Publication Release Date: April 14, 2005
- 8 -
Revision A3
7. REGISTER FOR LPC MODE
There are two kinds of registers on this device, the General Purpose Input Registers and Product
Identification Registers. Users can access these registers through respective address in the 4Gbytes
memory map. There are detail descriptions in the sections below.
7.1 General Purpose Inputs Register for LPC Mode
This register reads the FGPI[4:0] pins on the W39V040B.This is a pass-through register which can read
via memory address FBC0100(hex). Since it is pass-through register, there is no default value.
GPI Register Table
BIT
7
5
4
3
2
1
0
FUNCTION
Reserved
Read FGPI4 pin status
Read FGPI3 pin status
Read FGPI2 pin status
Read FGPI1 pin status
Read FGPI0 pin status
7.2 Identification Input Pins ID[3:0]
These pins are part of mechanism that allows multiple parts to be used on the same bus. The boot
device should be 0000b. And all the subsequent parts should use the up-count strapping. Note that a
1M byte ROM will occupy two Ids. For example: a 1MByte ROM's ID is 0000b, the next ROM's ID is
0010b. These pins all are pulled down with internal resistor.
7.3 Product Identification Registers
In the LPC interface mode, a read from FBC, 0000(hex) can output the manufacturer code, DA(hex). A
read from FBC, 0001(hex) can output the device code 54(hex).
There is an alternative software method (six commands bytes) to read out the Product Identification in
both the Programmer interface mode and the LPC interface mode. Thus, the programming equipment
can automatically matches the device with its proper erase and programming algorithms.
In the software access mode, a six-byte (or JEDEC 3-byte) command sequence can be used to access
the product ID for programmer interface mode. A read from address 0000(hex) outputs the
manufacturer code, DA(hex). A read from address 0001(hex) outputs the device code, 54(hex). The
product ID operation can be terminated by a three-byte command sequence or an alternate one-byte
command sequence (see Command Definition table for detail).
相關PDF資料 |
PDF描述 |
|---|---|
| W39V040C | 512K 】 8 CMOS FLASH MEMORY WITH LPC INTERFACE |
| W39V040CP | 512K 】 8 CMOS FLASH MEMORY WITH LPC INTERFACE |
| W39V040CPZ | 512K 】 8 CMOS FLASH MEMORY WITH LPC INTERFACE |
| W39V040CQ | 512K 】 8 CMOS FLASH MEMORY WITH LPC INTERFACE |
| W39V040CQZ | 512K 】 8 CMOS FLASH MEMORY WITH LPC INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W39V040BQ | 制造商:WINBOND 制造商全稱:Winbond 功能描述:W39V040B |
| W39V040BQZ | 制造商:WINBOND 制造商全稱:Winbond 功能描述:W39V040B |
| W39V040C | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512K 】 8 CMOS FLASH MEMORY WITH LPC INTERFACE |
| W39V040CP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512K 】 8 CMOS FLASH MEMORY WITH LPC INTERFACE |
| W39V040CPZ | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512K 】 8 CMOS FLASH MEMORY WITH LPC INTERFACE |
發布緊急采購，3分鐘左右您將得到回復。