- 您現在的位置：買賣IC網 > PDF目錄363898 > W78E51B-24 (WINBOND ELECTRONICS CORP) 8-BIT MTP MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W78E51B-24 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT MTP MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP40 |
| 封裝： | DIP-40 |
| 文件頁數： | 5/23頁 |
| 文件大?。?/td> | 324K |
| 代理商： | W78E51B-24 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁
Preliminary W78E51B
Publication Release Date: December 1998
- 5 -
Revision A1
1.
INT2
/ INT3
Two additional external interrupts,
INT2
and INT3 , whose functions are similar to those of external
interrupt 0 and 1 in the standard 80C52. The functions/status of these interrupts are
determined/shown by the bits in the XICON (External Interrupt Control) register. The XICON register
is bit-addressable but is not a standard register in the standard 80C52. Its address is at 0C0H. To
set/clear bits in the XICON register, one can use the "SETB (/CLR) bit" instruction. For example,
"SETB 0C2H" sets the EX2 bit of XICON.
XICON - external interrupt control (C0H)
PX3
EX3
IE3
IT3
PX2
EX2
IE2
IT2
PX3: External interrupt 3 priority high if set
EX3: External interrupt 3 enable if set
IE3: If IT3 = 1, IE3 is set/cleared automatically by hardware when interrupt is detected/serviced
IT3: External interrupt 3 is falling-edge/low-level triggered when this bit is set/cleared by software
PX2: External interrupt 2 priority high if set
EX2: External interrupt 2 enable if set
IE2: If IT2 = 1, IE2 is set/cleared automatically by hardware when interrupt is detected/serviced
IT2: External interrupt 2 is falling-edge/low-level triggered when this bit is set/cleared by software
Eight-source interrupt informations:
INTERRUPT
SOURCE
VECTOR
ADDRESS
POLLING
SEQUENCE WITHIN
PRIORITY LEVEL
0 (highest)
1
2
3
4
5
6 (lowest)
ENABLE
REQUIRED
SETTINGS
IE.0
IE.1
IE.2
IE.3
IE.4
XICON.2
XICON.6
INTERRUPT
TYPE
EDGE/LEVEL
TCON.0
-
TCON.2
-
-
XICON.0
XICON.3
External Interrupt 0
Timer/Counter 0
External Interrupt 1
Timer/Counter 1
Serial Port
External Interrupt 2
External Interrupt 3
03H
0BH
13H
1BH
23H
33H
3BH
2. PORT4
Another bit-addressable port P4 is also available and only 4 bits (P4<3:0>) can be used. This port
address is located at 0D8H with the same function as that of port P1, except the P4.3 and P4.2 are
alternative function pins. It can be used as general I/O pins or external interrupt input sources (
INT2
,
INT3 ).
Example:
P4
REG
0D8H
MOV
P4, #0AH
; Output data "A" through P4.0
P4.3.
MOV
A, P4
; Read P4 status to Accumulator.
SETB
P4.0
; Set bit P4.0
CLR
P4.1
; Clear bit P4.1
相關PDF資料 |
PDF描述 |
|---|---|
| W78E51B-40 | 8-BIT MTP MICROCONTROLLER |
| W78E51B | 8-BIT MTP Monitor Microcontroller(多次可編程的8位的監視微控制器) |
| W78E51BF-24 | 8-BIT MTP MICROCONTROLLER |
| W78E51BF-40 | 8-BIT MTP MICROCONTROLLER |
| W78E51BP-40 | 8-BIT MTP MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78E51B-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
| W78E51BF-24 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
| W78E51BF-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
| W78E51BP-24 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
| W78E51BP-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。