- 您現在的位置：買賣IC網 > PDF目錄363898 > W78E51BF-40 (WINBOND ELECTRONICS CORP) 8-BIT MTP MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W78E51BF-40 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT MTP MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | PLASTIC, QFP-44 |
| 文件頁數： | 8/23頁 |
| 文件大小： | 324K |
| 代理商： | W78E51BF-40 |
Preliminary W78E51B
- 8 -
Typical Watch-Dog time-out period when OSC = 20 MHz
PS2 PS1 PS0
0 0 0
0 1 0
0 0 1
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
WATCHDOG TIME-OUT PERIOD
19.66 mS
39.32 mS
78.64 mS
157.28 mS
314.57 mS
629.14 mS
1.25 S
2.50 S
Clock
The W78E51B is designed to be used with either a crystal oscillator or an external clock. Internally,
the clock is divided by two before it is used. This makes the W78E51B relatively insensitive to duty
cycle variations in the clock. The W78E51B incorporates a built-in crystal oscillator. To make the
oscillator work, a crystal must be connected across pins XTAL1 and XTAL2. In addition, a load
capacitor must be connected from each pin to ground. An external clock source should be connected
to pin XTAL1. Pin XTAL2 should be left unconnected. The XTAL1 input is a CMOS-type input, as
required by the crystal oscillator.
Power Management
Idle Mode
The idle mode is entered by setting the IDL bit in the PCON register. In the idle mode, the internal
clock to the processor is stopped. The peripherals and the interrupt logic continue to be clocked. The
processor will exit idle mode when either an interrupt or a reset occurs.
Power-down Mode
When the PD bit of the PCON register is set, the processor enters the power-down mode. In this
mode all of the clocks are stopped, including the oscillator. The only way to exit power-down mode is
by a reset.
Reset
The external RESET signal is sampled at S5P2. To take effect, it must be held high for at least two
machine cycles while the oscillator is running. An internal trigger circuit in the reset line is used to
deglitch the reset line when the W78E51B is used with an external RC network. The reset logic also
has a special glitch removal circuit that ignores glitches on the reset line.
During reset, the ports are initialized to FFH, the stack pointer to 07H, PCON (with the exception of
bit 4) to 00H, and all of the other SFR registers except SBUF to 00H. SBUF is not reset.
ON-CHIP MTP ROM CHARACTERISTICS
The W78E51B has several modes to program the on-chip MTP-ROM. All these operations are
configured by the pins RST, ALE,
PSEN
, A9CTRL(P3.0), A13CTRL(P3.1), A14CTRL(P3.2),
OECTRL(P3.3), CE(P3.6), OE(P3.7), A0(P1.0) and V
PP
(
EA
). Moreover, the A15
A0(P2.7
P2.0,
相關PDF資料 |
PDF描述 |
|---|---|
| W78E51BP-40 | 8-BIT MTP MICROCONTROLLER |
| W78E51C | 8 bit micocontroller |
| W78E51 | 8-BIT MTP Monitor Microcontroller(多次可編程的8位的監視微控制器) |
| W78E52 | 8-BIT MTP Monitor Microcontroller(多次可編程的8位的監視微控制器) |
| W78E56B | 8-BIT Microcontroller(8位的微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78E51BP-24 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
| W78E51BP-40 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
| W78E51C | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8 bit micocontroller |
| W78E51C_06 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78E51P-16 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。