- 您現在的位置：買賣IC網 > PDF目錄363900 > W78LE812F-24 (WINBOND ELECTRONICS CORP) 8-BIT MTP MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W78LE812F-24 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT MTP MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | PLASTIC, QFP-44 |
| 文件頁數： | 11/25頁 |
| 文件大小： | 338K |
| 代理商： | W78LE812F-24 |
W78LE812
Publication Release Date: February 1999
- 11 -
Revision A2
Clock
The W78LE812 is designed to be used with either a crystal oscillator or an external clock. Internally,
the clock is divided by two before it is used. This makes the W78LE812 relatively insensitive to duty
cycle variations in the clock. The W78LE812 incorporates a built-in crystal oscillator. To make the
oscillator work, a crystal must be connected across pins XTAL1 and XTAL2. In addition, a load
capacitor must be connected from each pin to ground. An external clock source should be connected
to pin XTAL1. Pin XTAL2 should be left unconnected. The XTAL1 input is a CMOS-type input, as
required by the crystal oscillator.
Power Management
Idle Mode
The idle mode is entered by setting the IDL bit in the PCON register. In the idle mode, the internal
clock to the processor is stopped. The peripherals and the interrupt logic continue to be clocked. The
processor will exit idle mode when either an interrupt or a reset occurs.
Power-down Mode
When the PD bit in the PCON register is set, the processor enters the power-down mode. In this
mode all of the clocks are stopped, including the oscillator.
AUXR - Auxiliary Register
Bit:
7
6
5
4
3
2
1
0
-
-
-
-
-
-
-
AO
Mnemonic: AUXR
Address: 8Eh
AO:
Turn off ALE signal.
Reduce EMI Emission
Because of the on-chip MTP-ROM, when a program is running in internal ROM space, the ALE will be
unused. The transition of ALE will cause noise, so it can be turned off to reduce the EMI emission if it
is not needed. Turning off the ALE signal transition only requires setting the bit 0 of the AUXR SFR,
which is located at 08Eh. When ALE is turned off, it will be reactivated when the program accesses
external ROM/RAM data or jumps to execute an external ROM code. The ALE signal will turn off
again after it has been completely accessed or the program returns to internal ROM code space..
Reset
The external RESET signal is sampled at S5P2. To take effect, it must be held high for at least two
machine cycles while the oscillator is running. An internal trigger circuit in the reset line is used to
deglitch the reset line when the W78LE812 is used with an external RC network. The reset logic also
has a special glitch removal circuit that ignores glitches on the reset line.
During reset, the ports are initialized to FFH, the stack pointer to 07H, PCON (with the exception of
bit 4) to 00H, and all of the other SFR registers except SBUF to 00H. SBUF is not reset.
相關PDF資料 |
PDF描述 |
|---|---|
| W78LE812P-24 | 8-BIT MTP MICROCONTROLLER |
| W78LE812-24 | 8-BIT MTP MICROCONTROLLER |
| W79E201 | 8-BIT MICROCONTROLLER |
| W79E201A16FN | 8-BIT MICROCONTROLLER |
| W79E201A16LN | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78LE812P-24 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MTP MICROCONTROLLER |
| W78M032A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78M032A24DL | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78M032A24FL | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78M032A24PL | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。