- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C92 (WINBOND ELECTRONICS CORP) PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER PDF資料下載
參數資料
| 型號： | W89C92 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 網絡接口 |
| 英文描述： | PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| 中文描述： | DATACOM, ETHERNET TRANSCEIVER, PDIP16 |
| 封裝： | DIP-16 |
| 文件頁數： | 23/48頁 |
| 文件大小： | 395K |
| 代理商： | W89C92 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
W89C926 PENTIC+
Publication Release Date: January 1996
- 23 -
Revision A1
out before the buffer ring overflows. This is done through a remote DMA read operation, which is
simply a "IN" command on the PC.
SHARED MEMORY MODE OPERATION
In this mode, the local memory is mapped as part of the system memory. When it requires data
transmission, the host fills the transmit buffer SRAM by a memory move operation and then issues a
transmit command to the PENTIC+. When it receives data, the PENTIC+ will generate an interrupt
to the host by asserting IREQ when one or more packets have been received. The PENTIC+ will then
place the packets into the shared memory. The host should check the shared memory and remove
the data before the buffer ring overflows.
Bus arbitration is performed between the host and LCE core for shared memory usage. When
memory accesses are issued, the arbiter will grant the bus master an acknowledge signal, which is a
BACK to the LCE or a WAIT signal to the host. There is no predefined priority in the PENTIC+; bus
arbitration is performed on a first-come, first-served basis.
To implement the shared memory mode, the PENTIC+ uses memory mapping register A (MMA) and
memory mapping register B (MMB) for memory mapping control. Since the PENTIC+ will operate in
16-bit shared memory operation at shared memory base address 00000H only, 0s should be written
to MMB and bit 0 to 5 of MMA. The contents of the MMA are described below.
MMA (Memory Mapping Register A)
MMA is used for memory enable and software reset. It is located in I/O space, 00H, and can be ac-
cessed only in shared memory mode.
Access Address: IOBASE + 00H
Access Type: write-only
BIT
SYMBOL
0-5
-
Reserved. Should be set to 0.
6
MEN
If this bit is high, the buffer memory may be accessed by the
system; if it is low, the buffer memory access is disabled. This
bit is 0 at power-on.
7
SRESET
A shared memory mode software reset is issued when a 1 is
written to this bit. Writing a 0 to this bit will clear the software
reset. This bit is 0 at power-on.
DESCRIPTION
AUTO MEDIA-SWITCHING FUNCTION
The PENTIC+ also provides a user-friendly auto media-switching function. If the PENTIC+ is
configured at the TPI, link checking is enabled, and the UTP link is broken, the PENTIC+ will detect
the link status and switch to the BNC port immediately. After the UTP link is repaired, the PENTIC+
will detect the good link and switch back to the TPI again.
If, however, the PENTIC+ is not configured at the TPI or link checking is disabled, the auto media-
switching function will be disabled.
相關PDF資料 |
PDF描述 |
|---|---|
| W89C926 | PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| W89C926F | 10M PCMCIA Ethernet Network Interface Controller |
| W89C940 | ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
| W89C982 | INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | INTEGRATED MULTIPLE REPEATER II |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W89C926 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| W89C926F | 制造商:WINBOND 制造商全稱:Winbond 功能描述:10M PCMCIA Ethernet Network Interface Controller |
| W89C926PENTIC+ | 制造商:WINBOND 制造商全稱:Winbond 功能描述:PCMCIA ETHERNET NETWORK TWISTED PAIR INTERFACE CONTROLLER |
| W89C92P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M CMOS Coaxial Transceiver |
| W89C940 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
發布緊急采購，3分鐘左右您將得到回復。