- 您現在的位置：買賣IC網 > PDF目錄363904 > W91030 (WINBOND ELECTRONICS CORP) Low Power CMOS IC For Caller indentification(用于通信中呼叫確認的低功耗CMOS集成電路芯片) PDF資料下載
參數資料
| 型號： | W91030 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 無繩電話/電話 |
| 英文描述： | Low Power CMOS IC For Caller indentification(用于通信中呼叫確認的低功耗CMOS集成電路芯片) |
| 中文描述： | TELEPHONE CALLING NO IDENT CKT, PDIP24 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-24 |
| 文件頁數： | 12/30頁 |
| 文件大?。?/td> | 359K |
| 代理商： | W91030 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Preliminary W91030
- 12 -
Demodulated
internal
bit stream
start
0
b0
b1
b2
b3
b4
b5
b6
b7
1
0
stop
stop
start
DATA
b0 b1 b2 b3 b4 b5 b6 b7
DCLK
FDRN
1/f
DCLK1
b7
b6
b5
1
b0
b0
b7
b6
t
DDS
t
DDH
Nth byte data
(N + 1)th byte data
(N - 1)th byte data
Nth byte data
t
RL
Note 2
Note 1
1. FDRN cleared to high by DCLK.
2. FDRN not cleared, low for maximum time (1/2 bit width).
Notes:
Figure 7-8. Serial Data Interface Timing of FSK Demodulation in Mode 1
Other Functions
Operation Modes
The two operation modes of the W91030 are known as M-mode and C-Mode and the timing
difference related to these two mode are on the INTN and ALGO/DET pins.
In M-mode (MODE pin high), the ALGO/DET pin is used as a dual tone alert signal guard time detect
output. The microcontroller must monitor the RNGON pin during ring detection, monitor the ALGO pin
during alert tone detection and monitor the FCDN pin during FSK demodulation.
In C-mode (MODE pin low), the ring detect output, alert guard time output and FSK carrier detect
outpout also will be reflected on the ALGO/DET output pin. The microcontroller may monitor the
ALGO/DET pin during ring detection, during alert tone detection and during FSK demodulation. The
interrupt outputs only after the end of the alerting guard time when the dual tone alert signal has been
detected. The microcontroller must enable the FSK demodulation when an interrupt occurs at the end
of the alerting guard time detection.
Interrupt
The interrupt INTN is an open drain output and is used to interrupt the microcontroller. Either RNGON
low, FDRN low or ALGO high (in M-mode) will set INTN low and will remain low until all of these three
pins return to an inactive state. The microcontroller must read these pins to know what kind of
interrupt occurred and to make the correct interrupt response. In C-mode, the interrupt outputs only
after the end of the alerting guard time when the dual tone alert signal has been detected.
When the system is powered on, there is no charge on the capacitors. The voltage on the RNGRC pin
is low and RNGON will be low. Also the voltage on the ALGRC pin is high and ALGO will be high if
the SLEEP pin is low. This will cause an interrupt upon power up which will not be cleared until both
相關PDF資料 |
PDF描述 |
|---|---|
| W91031 | LOW POWER CMOS INTERGRATED CIRCUIT |
| W91031S | Calling Line Identifier |
| W91080 | Tone/Pulse Dialer With Handfree And Keytone Fuctions And One Number Memory(具有一個數碼存儲器免提和主鍵音功能的音頻/脈沖撥號器) |
| W91080A | Tone/Pulse Dialer With Handfree And Keytone Fuctions And One Number Memory(具有一個數碼存儲器免提和主鍵音功能的音頻/脈沖撥號器) |
| W91082N | Tone Generator With μC Serial Interface(具有微控制器接口的音頻發生器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W91030B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:CALLING LINE IDENTIFIER |
| W91030B/BS | 制造商:WINBOND 制造商全稱:Winbond 功能描述:Calling Line Identifier |
| W91031 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:LOW POWER CMOS INTERGRATED CIRCUIT |
| W91031S | 制造商:WINBOND 制造商全稱:Winbond 功能描述:Calling Line Identifier |
| W91031SG | 功能描述:IC CALL LINE IDENT 24-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
發布緊急采購，3分鐘左右您將得到回復。