- 您現在的位置：買賣IC網 > PDF目錄363908 > W981208AH-8H (WINBOND ELECTRONICS CORP) x8 SDRAM PDF資料下載
參數資料
| 型號： | W981208AH-8H |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | DRAM |
| 英文描述： | x8 SDRAM |
| 中文描述： | 16M X 8 SYNCHRONOUS DRAM, 6 ns, PDSO54 |
| 封裝： | 0.400 INCH, 0.80 MM PITCH, TSOP2-54 |
| 文件頁數： | 11/44頁 |
| 文件大?。?/td> | 2177K |
| 代理商： | W981208AH-8H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
W981208AH
4M x 8 bit x 4 Banks SDRAM
Revision 1.0 Publication Release Date: March, 1999
- 11 -
Burst Write Command
The Burst Write command is initiated by applying logic low level to CS, CAS and WE while holding RAS high at the rising
edge of the clock. The address inputs determine the starting column address. Data for the first burst write cycle must be applied
on the DQ pins on the same clock cycle that the Write Command is issued. The remaining data inputs must be supplied on each
subsequent rising clock edge until the burst length is completed. Data supplied to the DQ pins after burst finishes will be
ignored.
Read Interrupted by a Read
A Burst Read may be interrupted by another Read Command. When the previous burst is interrupted, the remaining addresses
are overridden by the new read address with the full burst length. The data from the first Read Command continues to appear on
the outputs until the CAS latency from the interrupting Read Command the is satisfied.
Read Interrupted by a Write
To interrupt a burst read with a Write Command, DQM may be needed to place the DQs (output drivers) in a high impedance
state to avoid data contention on the DQ bus. If a Read Command will issue data on the first and second clocks cycles of the
write operation, DQM is needed to insure the DQs are tri-stated. After that point the Write Command will have control of the
DQ bus and DQM masking is no longer needed.
Write Interrupted by a Write
A burst write may be interrupted before completion of the burst by another Write Command. When the previous burst is
interrupted, the remaining addresses are overridden by the new address and data will be written into the device until the
programmed burst length is satisfied.
Write Interrupted by a Read
A Read Command will interrupt a burst write operation on the same clock cycle that the Read Command is activated. The DQs
must be in the high impedance state at least one cycle before the new read data appears on the outputs to avoid data contention.
When the Read Command is activated, any residual data from the burst write cycle will be ignored.
Burst Stop Command
A Burst Stop Command may be used to terminate the existing burst operation but leave the bank open for future Read or Write
Commands to the same page of the active bank, if the burst length is full page. Use of the Burst Stop Command during other burst
length operations is illegal. The Burst Stop Command is defined by having RAS and CAS high with CS and WE low at the rising
edge of the clock. The data DQs go to a high impedance state after a delay which is equal to the CAS Latency in a burst read
cycle interrupted by Burst Stop. If a Burst Stop Command is issued during a full page burst write operation, then any residual data
from the burst write cycle will be ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| W981208BH-7 | x8 SDRAM |
| W981208BH-75 | x8 SDRAM |
| W981208BH-8H | x8 SDRAM |
| W981216 | 2M x 16 bit x 4 Banks SDRAM |
| W981216AH | 2M x 16 bit x 4 Banks SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W981208BH | 制造商:WINBOND 制造商全稱:Winbond 功能描述:4M x 4 BANKS x 8 BIT SDRAM |
| W981208BH-7 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:x8 SDRAM |
| W981208BH-75 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:x8 SDRAM |
| W981208BH-8H | 制造商:WINBOND 制造商全稱:Winbond 功能描述:x8 SDRAM |
| W981216 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:2M x 16 bit x 4 Banks SDRAM |
發布緊急采購，3分鐘左右您將得到回復。