- 您現在的位置：買賣IC網 > PDF目錄363913 > WF256K16-60CC5A (Electronic Theatre Controls, Inc.) 5V FLASH MODULE PDF資料下載
參數資料
| 型號： | WF256K16-60CC5A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 5V FLASH MODULE |
| 中文描述： | 5V的閃存模塊 |
| 文件頁數： | 3/11頁 |
| 文件大小： | 201K |
| 代理商： | WF256K16-60CC5A |
White Microelectronics Phoenix, AZ (602) 437-1520
7
F
3
WF128K16, WF256K16-XCX5
PRINCIPLES OF OPERATION
WRITE
Device erasure and programming are accomplished via the
command register. The contents of the register serve as input
to the internal state machine. The state machine outputs
dictate the function of the device.
The command register itself does not occupy an addressable
memory location. The register is a latch used to store the
commands, along with address and data information needed to
execute the command. The command register is written by
bringing Write-Enable to a logic-low level (V
IL
), while Chip-Select
is low and OE is at V
IH
. Addresses are latched on the falling edge
of the Write-Enable while data is latched on the rising edge of the
WE pulse. Standard microprocessor write timings are used. Refer
to AC Program characteristics, Figures 4 and 7.
TABLE 1 - BUS OPERATIONS
Operation
CS
OE
WE
A
0
A
1
A
9
I/O
Read
L
L
H
A
0
A
1
A
9
D
OUT
Standby
H
X
X
X
X
X
HIGH Z
Output Disable
L
H
H
X
X
X
HIGH Z
Write
L
H
L
A
0
A
1
A
9
D
IN
Enable Sector Protect
L
V
ID
L
X
X
V
ID
X
Verify Sector Protect
L
L
H
L
H
V
ID
Code
The following principles of operation of the WF128K16-XCX5
and WF256K16-XCX5 are applicable to each 128K x 8 memory
chip inside the MCM. Programming of the device is accom-
plished by executing the program command sequence. The
program algorithm, which is an internal algorithm, automati-
cally times the program pulse widths and verifies proper cell
margin. Sectors can be programmed and verified in less than 0.3
seconds. Erase is accomplished by executing the erase
command sequence. The erase algorithm, which is internal,
automatically preprograms the array if it is not already
programmed before executing the erase operation. During
erase, the device automatically times the erase pulse widths
and verifies proper cell margin. The entire memory is typically
erased and verified in three seconds (including pre-program-
ming).
BUS OPERATIONS
READ
The device has two control functions, both of which must be
logically active, to obtain data at the outputs. Chip-Select (CS)
is the power control and should be used for device selection.
Output-Enable (OE) is the output control and should be used to
gate data to the output pins. Figure 3 illustrates read timing
waveforms.
OUTPUT DISABLE
With Output-Enable at a logic-high level (V
IH
), output from the
device is disabled. Output pins are placed in a high
impedance state.
STANDBY MODE
The device has two standby modes, a CMOS standby mode (CS
input held at V
CC
+ 0.5V), and a TTL standby mode (CS is held
V
IH
). In the standby mode the outputs are in a high impedance
state, independent of the OE input.
If the device is deselected during erasure or programming, the
device will draw active current until the operation is completed.
相關PDF資料 |
PDF描述 |
|---|---|
| WF256K16-60CI5 | 5V FLASH MODULE |
| WF256K16-60CI5A | 5V FLASH MODULE |
| WF256K16-60CM5 | 5V FLASH MODULE |
| WF256K16-60CM5A | 5V FLASH MODULE |
| WF256K16-60CQ5 | 5V FLASH MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| WF256K16-60CI5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5V FLASH MODULE |
| WF256K16-60CI5A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5V FLASH MODULE |
| WF256K16-60CM5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5V FLASH MODULE |
| WF256K16-60CM5A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5V FLASH MODULE |
| WF256K16-60CQ5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5V FLASH MODULE |
發布緊急采購，3分鐘左右您將得到回復。