- 您現在的位置：買賣IC網 > PDF目錄373913 > AD7705BN (ANALOG DEVICES INC) ECONOLINE: REC2.2-S_DR/H1 - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- UL94V-0 Package Material- Continuous Short Circiut Protection- Internal SMD design- 100% Burned In- Efficiency to 75% PDF資料下載
參數資料
| 型號： | AD7705BN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | ECONOLINE: REC2.2-S_DR/H1 - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- UL94V-0 Package Material- Continuous Short Circiut Protection- Internal SMD design- 100% Burned In- Efficiency to 75% |
| 中文描述： | 2-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDIP16 |
| 封裝： | 0.300 INCH, PLASTIC, MS-001AB, DIP-16 |
| 文件頁數： | 17/32頁 |
| 文件大小： | 264K |
| 代理商： | AD7705BN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7705/AD7706
–17–
REV. A
Bipolar or unipolar options are chosen by programming the
B
/U
bit of the Setup Register. This programs the channel for either
unipolar or bipolar operation. Programming the channel for
either unipolar or bipolar operation does not change any of the
input signal conditioning, it simply changes the data output
coding and the points on the transfer function where calibra-
tions occur.
REFERENCE INPUT
The AD7705/AD7706’s reference inputs, REFIN(+) and
REFIN(–), provide a differential reference input capability.
The common-mode range for these differential inputs is from
GND to V
DD
. The nominal reference voltage, V
REF
(REFIN(+)–
REFIN(–)), for specified operation, is +2.5V for the AD7705/
AD7706 operated with a V
DD
of 5 V and +1.225V for the
AD7705/AD7706 operated with a V
DD
of 3 V. The part is func-
tional with V
REF
voltages down to 1 V, but with degraded per-
formance as the output noise will, in terms of LSB size, be larger.
REFIN(+) must always be greater than REFIN(–) for correct
operation of the AD7705/AD7706.
Both reference inputs provide a high impedance, dynamic load
similar to the analog inputs in unbuffered mode. The maximum
dc input leakage current is
±
1 nA over temperature, and source
resistance may result in gain errors on the part. In this case, the
sampling switch resistance is 5k
typ and the reference capaci-
tor (C
REF
) varies with gain. The sample rate on the reference
inputs is f
CLKIN
/64 and does not vary with gain. For gains of 1
and 2, C
REF
is 8pF; for a gain of 16, it is 5.5pF, for a gain of
32, it is 4.25 pF, for a gain of 64, it is 3.625 pF and for a gain of
128, it is 3.3125pF.
The output noise performance outlined in Tables I through IV
is for an analog input of 0V, which effectively removes the
effect of noise on the reference. To obtain the same noise per-
formance as shown in the noise tables over the full input range
requires a low noise reference source for the AD7705/AD7706.
If the reference noise in the bandwidth of interest is excessive, it
will degrade the performance of the AD7705/AD7706. In appli-
cations where the excitation voltage for the bridge transducer on
the analog input also derives the reference voltage for the part,
the effect of the noise in the excitation voltage will be removed
as the application is ratiometric. Recommended reference volt-
age sources for the AD7705 with a V
DD
of 5 V include the
AD780, REF43 and REF192, while the recommended reference
sources for the AD7705 operated with a V
DD
of 3 V include the
AD589 and AD1580. It is generally recommended to decouple
the output of these references in order to further reduce the
noise level.
DIGITAL FILTERING
The AD7705/AD7706 contains an on-chip low-pass digital filter
which processes the output of the part’s sigma-delta modulator.
Therefore, the part not only provides the analog-to-digital con-
version function but also provides a level of filtering. There are a
number of system differences when the filtering function is
provided in the digital domain rather than the analog domain
and the user should be aware of these.
First, since digital filtering occurs after the A-to-D conversion
process, it can remove noise injected during the conversion
process. Analog filtering cannot do this. Also, the digital filter
can be made programmable far more readily than an analog
filter. Depending on the digital filter design, this gives the user
the capability of programming cutoff frequency and output
update rate.
On the other hand, analog filtering can remove noise superim-
posed on the analog signal before it reaches the ADC. Digital
filtering cannot do this and noise peaks riding on signals near
full scale have the potential to saturate the analog modulator
and digital filter, even though the average value of the signal is
within limits. To alleviate this problem, the AD7705/AD7706
has overrange headroom built into the sigma-delta modulator
and digital filter, which allows overrange excursions of 5%
above the analog input range. If noise signals are larger than
this, consideration should be given to analog input filtering, or
to reducing the input channel voltage so that its full-scale is half
that of the analog input channel full-scale. This will provide an
overrange capability greater than 100% at the expense of reduc-
ing the dynamic range by 1 bit (50%).
In addition, the digital filter does not provide any rejection at
integer multiples of the digital filter’s sample frequency. How-
ever, the input sampling on the part provides attenuation at
multiples of the digital filter’s sampling frequency so that the
unattenuated bands actually occur around multiples of the
sampling frequency f
S
(as defined in Table XV). Thus the
unattenuated bands occur at n
×
f
S
(where n = 1, 2, 3 . . .). At
these frequencies, there are frequency bands,
±
f
3
dB
wide f
3
dB
is
the cutoff frequency of the digital filter) at either side where
noise passes unattenuated to the output.
Filter Characteristics
The AD7705/AD7706’s digital filter is a low-pass filter with a
(sinx/x)
3
response (also called sinc
3
). The transfer function for
this filter is described in the z-domain by:
H
(
z
)
=
1
N
×
1
Z
–
N
1
Z
–1
3
and in the frequency domain by:
H
(
f
)
=
1
N
×
SIN
(
N
×π×
f
/
f
S
)
SIN
(
π×
f
/
f
S
)
3
where
N
is the ratio of the modulator rate to the output rate.
Phase Response:
∠
H
=
–3
π
(
N
–2)
×
f
/
f
S
Rad
Figure 4 shows the filter frequency response for a cutoff fre-
quency of 15.72Hz, which corresponds to a first filter notch
frequency of 60Hz. The plot is shown from dc to 390Hz. This
response is repeated at either side of the digital filter’s sample
frequency and at either side of multiples of the filter’s sample
frequency.
The response of the filter is similar to that of an averaging filter,
but with a sharper roll-off. The output rate for the digital filter
corresponds with the positioning of the first notch of the filter’s
frequency response. Thus, for the plot of Figure 12 where the
output rate is 60Hz, the first notch of the filter is at 60Hz. The
notches of this (sinx/x)
3
filter are repeated at multiples of the
first notch. The filter provides attenuation of better than 100dB
at these notches.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7705BR | ECONOLINE: REC2.2-S_DRW(Z)/H* - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- 4.5-9V, 9-18V, 18-36V, 36-72V Wide Input Range 2 : 1- UL94V-0 Package Material- Continuous Short Circiut Protection- Cost Effective- 100% Burned In- Efficiency to 84% |
| AD7705BRU | 3 V/5 V, 1 mW 2-/3-Channel 16-Bit, Sigma-Delta ADCs |
| AD7706 | 3 V/5 V, 1 mW 2-/3-Channel 16-Bit, Sigma-Delta ADCs |
| AD7706BN | ECONOLINE: REC2.2-S_DRW(Z)/H* - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- 4.5-9V, 9-18V, 18-36V, 36-72V Wide Input Range 2 : 1- UL94V-0 Package Material- Continuous Short Circiut Protection- Cost Effective- 100% Burned In- Efficiency to 84% |
| AD7706BR | 3 V/5 V, 1 mW 2-/3-Channel 16-Bit, Sigma-Delta ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7705BNZ | 功能描述:IC ADC 16BIT 2CH 16-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7705BNZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 1 mW, 2-/3-Channel, 16-Bit, Sigma-Delta ADCs |
| AD7705BR | 功能描述:IC ADC 16BIT 2CH 16-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7705BR-REEL | 功能描述:IC ADC 16BIT 2CH 16-SOIC T/R RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7705BR-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 500sps 16-bit Serial 16-Pin SOIC W T/R |
發布緊急采購，3分鐘左右您將得到回復。