- 您現在的位置：買賣IC網 > PDF目錄371075 > MC88915FN55PLCC (Motorola, Inc.) Low Skew CMOS PLL Clock Driver PDF資料下載
參數資料
| 型號： | MC88915FN55PLCC |
| 廠商： | Motorola, Inc. |
| 英文描述： | Low Skew CMOS PLL Clock Driver |
| 中文描述： | 低偏移的CMOS PLL時鐘驅動器 |
| 文件頁數： | 1/20頁 |
| 文件大?。?/td> | 216K |
| 代理商： | MC88915FN55PLCC |
SEMICONDUCTOR TECHNICAL DATA
1
REV 4
Motorola, Inc. 1997
1/97
"' '
" #&#$ %%
!( #$"!$
The MC88915T Clock Driver utilizes phase–locked loop technology to
lock its low skew outputs’ frequency and phase onto an input reference
clock. It is designed to provide clock distribution for high performance
PC’s and workstations. For a 3.3V version, see the MC88LV915T data
sheet.
The PLL allows the high current, low skew outputs to lock onto a single
clock input and distribute it with essentially zero delay to multiple
components on a board. The PLL also allows the MC88915T to multiply a
low frequency input clock and distribute it locally at a higher (2X) system
frequency. Multiple 88915’s can lock onto a single reference clock, which
is ideal for applications when a central system clock must be distributed
synchronously to multiple boards (see Figure 7).
Five “Q” outputs (Q0–Q4) are provided with less than 500 ps skew between their rising edges. The Q5 output is inverted (180
°
phase shift) from the “Q” outputs. The 2X_Q output runs at twice the “Q” output frequency, while the Q/2 runs at 1/2 the “Q”
frequency.
The VCO is designed to run optimally between 20 MHz and the 2X_Q Fmax specification. The wiring diagrams in Figure 5 detail
the different feedback configurations which create specific input/output frequency relationships. Possible frequency ratios of the
“Q” outputs to the SYNC input are 2:1, 1:1, and 1:2.
The FREQ_SEL pin provides one bit programmable divide–by in the feedback path of the PLL. It selects between divide–by–1
and divide–by–2 of the VCO before its signal reaches the internal clock distribution section of the chip (see the block diagram on
page 2). In most applications FREQ_SEL should be held high (
÷
1). If a low frequency reference clock input is used, holding
FREQ_SEL low (
÷
2) will allow the VCO to run in its optimal range (>20MHz and >40MHz for the TFN133 version).
In normal phase–locked operation the PLL_EN pin is held high. Pulling the PLL_EN pin low disables the VCO and puts the 88915
in a static “test mode”. In this mode there is no frequency limitation on the input clock, which is necessary for a low frequency board
test environment. The second SYNC input can be used as a test clock input to further simplify board–level testing (see detailed
description on page 11).
Pulling the OE/RST pin low puts the clock outputs 2X_Q, Q0–Q4, Q5 and Q/2 into a high impedance state (3–state). After the
OE/RST pin goes back high Q0–Q4, Q5 and Q/2 will be reset in the low state, with 2X_Q being the inverse of the selected SYNC
input. Assuming PLL_EN is low, the outputs will remain reset until the 88915 sees a SYNC input pulse.
A lock indicator output (LOCK) will go high when the loop is in steady–state phase and frequency lock. The LOCK output will go
low if phase–lock is lost or when the PLL_EN pin is low. The LOCK output will go high no later than 10ms after the 88915 sees a
SYNC signal and full 5V VCC.
Features
Five Outputs (Q0–Q4) with Output–Output Skew < 500 ps each being phase and frequency locked to the SYNC input
The phase variation from part–to–part between the SYNC and FEEDBACK inputs is less than 550 ps (derived from the tPD
specification, which defines the part–to–part skew)
Input/Output phase–locked frequency ratios of 1:2, 1:1, and 2:1 are available
Input frequency range from 5MHz – 2X_Q FMAX spec. (10MHz – 2X_Q FMAX for the TFN133 version)
Additional outputs available at 2X and +2 the system “Q” frequency. Also a Q (180
°
phase shift) output available
All outputs have
±
36 mA drive (equal high and low) at CMOS levels, and can drive either CMOS or TTL inputs. All inputs
are TTL–level compatible.
±
88mA IOL/IOH specifications guarantee 50
transmission line switching on the incident edge
Test Mode pin (PLL_EN) provided for low frequency testing. Two selectable CLOCK inputs for test or redundancy purposes.
All outputs can go into high impedance (3–state) for board test purposes
Lock Indicator (LOCK) accuracy indicates a phase–locked state
Yield Surface Modeling and YSM are trademarks of Motorola, Inc.
LOW SKEW CMOS
PLL CLOCK DRIVER
相關PDF資料 |
PDF描述 |
|---|---|
| MC88915T | LOW SKEW CMOS PLL CLOCK DRIVER |
| MC88915TFN133 | CONNECTOR ACCESSORY |
| MC88915TFN160 | LOW SKEW CMOS PLL CLOCK DRIVER |
| MC88915TFN55 | CONNECTOR ACCESSORY |
| MC88915TFN70 | CONNECTOR ACCESSORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC88915FN55R2 | 功能描述:IC DRIVER CLK PLL 55MHZ 28-PLCC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MC88915FN70 | 功能描述:IC DRIVER CLK PLL 70MHZ 28-PLCC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MC88915FN70PLCC | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Low Skew CMOS PLL Clock Driver |
| MC88915FN70R2 | 功能描述:IC DRIVER CLK PLL 70MHZ 28-PLCC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MC88915T | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:LOW SKEW CMOS PLL CLOCK DRIVER |
發布緊急采購，3分鐘左右您將得到回復。