- 您現在的位置：買賣IC網 > PDF目錄22061 > MSC7115VM1000 (Freescale Semiconductor)DSP 16BIT W/DDR CTRLR 400-MAPBGA PDF資料下載
參數資料
| 型號： | MSC7115VM1000 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 40/56頁 |
| 文件大小： | 0K |
| 描述： | DSP 16BIT W/DDR CTRLR 400-MAPBGA |
| 標準包裝： | 90 |
| 系列： | StarCore |
| 類型： | SC1400 內核 |
| 接口： | 主機接口，I²C，UART |
| 時鐘速率： | 266MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 400kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.20V |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 400-LFBGA |
| 供應商設備封裝： | 400-MAPBGA（17x17） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
Hardware Design Considerations
MSC7115 Low-Cost 16-bit DSP with DDR Controller Data Sheet, Rev. 11
Freescale Semiconductor
45
3.2.3
Power Planes
Each power supply pin (VDDC, VDDM, and VDDIO) should have a low-impedance path to the board power supply. Each GND pin
should be provided with a low-impedance path to ground. The power supply pins drive distinct groups of logic on the device.
The MSC7115 VDDC power supply pins should be bypassed to ground using decoupling capacitors. The capacitor leads and
associated printed circuit traces connecting to device power pins and GND should be kept to less than half an inch per capacitor
lead. A minimum four-layer board that employs two inner layers as power and GND planes is recommended. See Section 3.5
for DDR Controller power guidelines.
3.2.4
Decoupling
Both the I/O voltage and core voltage should be decoupled for switching noise. For I/O decoupling, use standard capacitor
values of 0.01
μF for every two to three voltage pins. For core voltage decoupling, use two levels of decoupling. The first level
should consist of a 0.01 F high frequency capacitor with low effective series resistance (ESR) and effective series inductance
(ESL) for every two to three voltage pins. The second decoupling level should consist of two bulk/tantalum decoupling
capacitors, one 10
μF and one 47 μF, (with low ESR and ESL) mounted as closely as possible to the MSC7115 voltage pins.
Additionally, the maximum drop between the power supply and the DSP device should be 15 mV at 1 A.
3.2.5
PLL Power Supply Filtering
The MSC7115 VDDPLL power signal provides power to the clock generation PLL. To ensure stability of the internal clock, the
power supplied to this pin should be filtered with capacitors that have low and high frequency filtering characteristics. VDDPLL
can be connected to VDDC through a 2 Ω resistor. VSSPLL can be tied directly to the GND plane. A circuit similar to the one
shown in Figure 31 is recommended. The PLL loop filter should be placed as closely as possible to the VDDPLL pin (which are
located on the outside edge of the silicon package) to minimize noise coupled from nearby circuits.The 0.01 F capacitor should
be closest to VDDPLL, followed by the 0.1 F capacitor, the 10 F capacitor, and finally the 2-Ω resistor to VDDC. These traces
should be kept short.
3.2.6
Power Consumption
You can reduce power consumption in your design by controlling the power consumption of the following regions of the device:
Extended core. Use the SC1400 Stop and Wait modes by issuing a stop or wait instruction.
Clock synthesis module. Disable the PLL, timer, watchdog, or DDR clocks or disable the CLKO pin.
AHB subsystem. Freeze or shut down the AHB subsystem using the GPSCTL[XBR_HRQ] bit.
Peripheral subsystem. Halt the individual on-device peripherals such as the DDR memory controller, HDI16, TDM,
UART, I2C, and timer modules.
For details, see the “Clocks and Power Management” chapter of the MSC711x Reference Manual.
Figure 31. PLL Power Supply Filter Circuits
VDDC
VDDPLL
2
Ω
0.1 F 0.01 F
10 F
相關PDF資料 |
PDF描述 |
|---|---|
| EBC17DRYI-S13 | CONN EDGECARD 34POS .100 EXTEND |
| ESC65DREH-S734 | CONN EDGECARD 130POS .100 EYELET |
| MAP40-3105 | PWR SUP TRI OUTPUT 40W 5V,12V-5V |
| MSC7115VF1000 | DSP 16BIT W/DDR CTRLR 400-MAPBGA |
| RBB60DHBT-S621 | EDGECARD 120POS DIP R/A .050 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSC7115VM800 | 功能描述:IC DSP PROCESSOR 16BIT 400MAPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| MSC7116 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Low-Cost 16-bit DSP with DDR Controller and 10/100 Mbps Ethernet MAC |
| MSC7116_08 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Low-Cost 16-bit DSP with DDR Controller and 10/100 Mbps Ethernet MAC |
| MSC7116VF1000 | 功能描述:數字信號處理器和控制器 - DSP, DSC 7116 STARLITE PB-BEARING RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| MSC7116VM1000 | 功能描述:數字信號處理器和控制器 - DSP, DSC 7116 STARLITE - PBF RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。