- 您現在的位置：買賣IC網 > PDF目錄363882 > W39L040 (WINBOND ELECTRONICS CORP) 512 K X 8 CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | W39L040 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | 512 K X 8 CMOS FLASH MEMORY |
| 中文描述： | 512 kX的8的CMOS閃存 |
| 文件頁數： | 5/27頁 |
| 文件大小： | 334K |
| 代理商： | W39L040 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
W39L040
Publication Release Date: February 10, 2003
- 5 -
Revision A3
Logical Inhibit
Writing is inhibited by holding any one of #OE = V
IL
, #CE = V
IH
, or #WE = V
IH
. To initiate a write cycle
#CE and #WE must be a logical zero while #OE is a logical one.
Power-up Write and Read Inhibit
Power-up of the device with #WE = #CE = V
IL
and #OE = V
IH
will not accept commands on the rising
edge of #WE except 5mS delay (see the power up timing in AC Characteristics). The internal state
machine is automatically reset to the read mode on power-up.
Command Definitions
Device operations are selected by writing specific address and data sequences into the command
register. Writing incorrect address and data values or writing them in the improper sequence will reset
the device to the read mode. "Command Definitions" defines the valid register command sequences.
Read Command
The device will automatically power-up in the read state. In this case, a command sequence is not
required to read data. Standard microprocessor read cycles will retrieve array data. This default value
ensures that no spurious alteration of the memory content occurs during the power transition.
The device will automatically returns to read state after completing an Embedded Program or
Embedded Erase algorithm.
Refer to the AC Read Characteristics and Waveforms for the specific timing parameters.
Auto-select Command
Flash memories are intended for use in applications where the local CPU can alter memory contents.
As such, manufacture and device codes must be accessible while the device resides in the target
system. PROM programmers typically access the signature codes by raising A9 to a high voltage.
However, multiplexing high voltage onto the address lines is not generally a desirable system design
practice.
The device contains an auto-select command operation to supplement traditional PROM programming
methodology. The operation is initiated by writing the auto-select command sequence into the
command register. Following the command write, a read cycle from address XX00H retrieves the
manufacture code of DAH. A read cycle from address XX01H returns the device code (W39L040 =
B6hex).
To terminate the operation, it is necessary to write the auto-select exit command sequence into the
register.
Byte Program Command
The device is programmed on a byte-by-byte basis. Programming is a four-bus-cycle operation. The
program command sequence is initiated by writing two "unlock" write cycles, followed by the program
set-up command. The program address and data are written next, which in turn initiate the Embedded
program algorithm. Addresses are latched on the falling edge of #CE or #WE, whichever happens
later and the data is latched on the rising edge of #CE or #WE, whichever happens first. The rising
edge of #CE or #WE (whichever happens first) begins programming using the Embedded Program
相關PDF資料 |
PDF描述 |
|---|---|
| W39L040P-70 | 512 K X 8 CMOS FLASH MEMORY |
| W39L040P-70B | 512 K X 8 CMOS FLASH MEMORY |
| W39L040P-70J | 512 K X 8 CMOS FLASH MEMORY |
| W39L040P-70K | GT 35C 7#12,28#16 SKT PLUG |
| W39L040P-90 | 512 K X 8 CMOS FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W39L040A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512K 】 8 CMOS FLASH MEMORY |
| W39L040A70B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512K 】 8 CMOS FLASH MEMORY |
| W39L040A90B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512K 】 8 CMOS FLASH MEMORY |
| W39L040AP70B | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512K 】 8 CMOS FLASH MEMORY |
| W39L040AP70Z | 制造商:WINBOND 制造商全稱:Winbond 功能描述:512K 】 8 CMOS FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。