- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C982 (WINBOND ELECTRONICS CORP) INTEGRATED MULTIPLE REPEATER II PDF資料下載
參數資料
| 型號： | W89C982 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | INTEGRATED MULTIPLE REPEATER II |
| 中文描述： | 集成的多中繼二 |
| 文件頁數： | 13/28頁 |
| 文件大小： | 277K |
| 代理商： | W89C982 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Preliminary W89C982AF
Publication Release Date: November 1996
- 13 -
Revision A1
Read Bit Rate Error Status of TP Ports
The bit rate error status of the TP ports can be read using this command. Bits 0 through 7 correspond
to the polarity status of TP ports 0 through 7. A "1" on the MSO bit indicates that a bit rate error has
occurred and a "0" indicates no bit rate error has occurred.
Read MJLP Status
The MAU jabber lock-up protection status can be accessed using this command. A "1" on the MSB
indicates the transmit function of the IMPR II has been inhibited. The status can also be cleared using
this command.
Read AUI Port Status
The AUI port status, including partition, bit rate error, SQE test, and loopback error, can be accessed
using different variations of this command. Four different specific commands can be used, as shown
in the following table.
MSI DATA
10001111
10001011
10001101
10001001
MSO DATA
PBSL0000
PBSL0000
PBSL0000
PBSL0000
CLEAR BITS
B, S, L read cleared. P not cleared.
S, L read cleared. P, B not cleared.
B read cleared. P, S, L not cleared.
P, B, S, L not cleared.
Enable AUI Port
When disabled, the AUI port can be re-enabled using this command. The AUI port will then carry out
normal transmitting and receiving operations. To reconnect a partitioned AUI port, the port must first
be disabled and then re-enabled using this command.
Disable AUI Port
This command is used to disable the AUI port. When the AUI port is disabled, all inputs (the carrier
sense and the SQE) to the AUI port will be ignored by the IMPR II and the IMPR II will not transmit
any signal on the AUI port. In addition, the partition machine for the AUI port will be forced into idle
status.
Enable TP Ports
This command is used to enable a disabled TP port, allowing it to perform normal transmitting and
receiving operations. To reconnect a partitioned TP port or force a TP port into link fail state, the port
must first be disabled and then re-enabled using this command.
Disable TP Ports
Each TP port can be disabled individually. Bits 0, 1, and 2 are used to indicate the TP port that is to
be disabled, as follows:
相關PDF資料 |
PDF描述 |
|---|---|
| W89C982AF | INTEGRATED MULTIPLE REPEATER II |
| W8NB80 | N - CHANNEL 800V - 1.2ohm - 7.5A - TO-247 PowerMESH MOSFET |
| W90100F | Embedded Micro-Controller(32位嵌入式的微控制器) |
| W90210F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
| W90220F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W89C982AF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
| W8C2-DNL | 制造商:Hwei Lung Precision Machinery 功能描述:TORCH 8 LED BLACK 2C |
| W8D10PF29033 | 制造商:TE Connectivity 功能描述: |
| W8D11PF29033 | 制造商:TE Connectivity 功能描述: |
| W8D16PF29023 | 制造商:TE Connectivity 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。