- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C982AF (WINBOND ELECTRONICS CORP) INTEGRATED MULTIPLE REPEATER II PDF資料下載
參數資料
| 型號： | W89C982AF |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | INTEGRATED MULTIPLE REPEATER II |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP100 |
| 封裝： | QFP-100 |
| 文件頁數： | 10/28頁 |
| 文件大小： | 277K |
| 代理商： | W89C982AF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Preliminary W89C982AF
- 10 -
The IMPR II provides one pin (XCOLRPT) for collision status report, two pins (M0/M1) for port status
report mode selection, and nine pins for port status report (AUIRPT, TP0-7RPT). XCOLRPT is active
when a collision occurs. Each of the nine port status report pins can directly report four aspects of the
port status. Which aspect of the network status is reported by these pins is determined by the two
mode selection pins, M1 and M0, as shown in the table below.
TP LINK/ACTIVITY
AUI COL/ACTIVITY
0
0
PARTITION
TP POLARITY
AUI LOOPBACK ERROR
1
0
UTILIZATION
UTILIZATION
M1
M0
0
1
1
1
When M0 and M1 are set to "0," the pins report TP link/activity and AUI COL/activity. In this mode, a
low output on AUIRPT and TP0-7RPT means all the TP ports are in the link fail state, a high means
all the TP ports are in link good state, and the AUI is in collision state, and a 10 Hz signal means
incoming packets are being received by the AUI/TP ports. (Note that the 10 Hz signal is still reported
if the ports are partitioned or disabled.) If M0 is set to "1" and M1 to "0," the port partition status will be
reported. In this mode, a "0" output means that all the ports are connected correctly, and a "1" means
that the AUI/TP ports are in a partition state. When M0 is set to "0" and M1 to "1," AUI loopback
errors and TP polarity status will be reported. In this mode, a "0" output means that the AUI loopback
and TP polarity are correct, and a "1" means that an AUI loopback error has been detected and the
TP port polarity is reversed. If M0 and M1 are both set to "1," the network utilization will be reported.
In this mode, each LED stands for 10% of utilization. The percentage of network utilization is shown
the following table.
% OF
UTILIZATION
AUI
LED
TP0
LED
TP1
LED
TP2
LED
TP3
LED
TP4
LED
TP5
LED
TP6
LED
TP7
LED
10%
v
30%
v
v
v
50%
v
v
v
v
v
90%
v
v
v
v
v
v
v
v
v
Using pins M1 and M0 and external transistors, the IMPR II can drive LEDs to indicate the status of
the AUI/TP ports sequentially; the application circuit for the LEDs is shown below. If a simple decoder
is connected to pins M1 and M0 and a switch circuit is connected to TP0RPT to TP7RPT, the TP port
link/activity, partition, polarity, and network utilization can be displayed simultaneously.
相關PDF資料 |
PDF描述 |
|---|---|
| W8NB80 | N - CHANNEL 800V - 1.2ohm - 7.5A - TO-247 PowerMESH MOSFET |
| W90100F | Embedded Micro-Controller(32位嵌入式的微控制器) |
| W90210F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
| W90220F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
| W90221F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W8C2-DNL | 制造商:Hwei Lung Precision Machinery 功能描述:TORCH 8 LED BLACK 2C |
| W8D10PF29033 | 制造商:TE Connectivity 功能描述: |
| W8D11PF29033 | 制造商:TE Connectivity 功能描述: |
| W8D16PF29023 | 制造商:TE Connectivity 功能描述: |
| W8D18PF29063 | 制造商:TE Connectivity 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。