- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C940 (WINBOND ELECTRONICS CORP) ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) PDF資料下載
參數資料
| 型號： | W89C940 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
| 中文描述： | ELANC -的PCI（雙絞線醚局域網控制器帶有PCI接口） |
| 文件頁數： | 18/61頁 |
| 文件大?。?/td> | 353K |
| 代理商： | W89C940 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
W89C940
18
Status Register
Bit Location
15
Attribute
R/W
Description
This bit will be set "1" by W89C940 when it detects a parity error,
even if parity error handling is disabled(as controlled by bit 6 in the
command register). A "write 1" operation on this bit will clear this
bit. This bit will be set "0" after it is cleared.
This bit will be set "1" by W89C940 when it assert the internal
SERR#. A "write 1" operation on this bit will clear this bit. This bit
will be set "0" after it is cleared. This bit is read only for 100 pin
package and is fixed to "0".
The W89C940 do not support PCI bus master function. This bit is
fixed to "0".
The W89C940 do not support PCI bus master function. This bit is
fixed to "0".
This bit will be set "1" by W89C940 when it terminates a
transaction with target-abort. A "write 1" operation on this bit will
clear this bit. This bit will be set "0" after it is cleared.
The Bit-10 is fixed to "0" and Bit-9 is fixed to "1". It indicated that
the W89C940 assert the DEVSEL# with medium speed.
The W89C940 do not support PCI bus master function. This bit is
fixed to "0".
The W89C940 support fast back-to-back transaction.
All of these bits are fixed to "0" internally. And no specific function
are related to these bits.
14
R/W
13
R
12
R
11
R/W
10~9
R
8
R
7
R
R
6~0
There are two cases that the W89C940 will initiate the target-abort. The first one is the addressing parity check
error cause internal SERR# asserted but without STOP# signal and the second one is the byte enable and
address check error that the STOP# is asserted. If addressing don't match the following table, the target doesn't
transfer the data, but terminate with target abort.
AD1
0
0
1
1
AD0
0
1
0
1
C/BE3#
X
X
X
0
C/BE2#
X
X
0
1
C/BE1#
X
0
1
1
C/BE0#
0
1
1
1
Revision I.D. Register
The revision I.D. is chosen by the vendor. It specifies a device specific revision identifier. Zero is an acceptable
value. It can be viewed as a vendor defined extension to the Device I.D. The content of this register will be
updated after power on by the EEPROM load operation. The revision ID should be programmed into the 23th
byte of the EEPROM for power on auto loading.
相關PDF資料 |
PDF描述 |
|---|---|
| W89C982 | INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | INTEGRATED MULTIPLE REPEATER II |
| W8NB80 | N - CHANNEL 800V - 1.2ohm - 7.5A - TO-247 PowerMESH MOSFET |
| W90100F | Embedded Micro-Controller(32位嵌入式的微控制器) |
| W90210F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W89C940F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M PCI-Bus Ethernet Network Interface Controller |
| W89C982 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
| W8C2-DNL | 制造商:Hwei Lung Precision Machinery 功能描述:TORCH 8 LED BLACK 2C |
| W8D10PF29033 | 制造商:TE Connectivity 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。