- 您現在的位置：買賣IC網 > PDF目錄363904 > W89C940 (WINBOND ELECTRONICS CORP) ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) PDF資料下載
參數資料
| 型號： | W89C940 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 英文描述： | ELANC-PCI (TWISTED-PAIR ETHER-LAN CONTROLLER WITH PCI INTERFACE) |
| 中文描述： | ELANC -的PCI（雙絞線醚局域網控制器帶有PCI接口） |
| 文件頁數： | 20/61頁 |
| 文件大小： | 353K |
| 代理商： | W89C940 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
W89C940
20
ROM-Base-Address Register
Bit
31~24
R/W
FFH
23~16
R/W
FFH
15~8
R/W
80H
7~0
R/W
01H
Attribute
Initial Value
The W89C940 supports 8Kx8, 16Kx8, 32Kx8, 64Kx8, 128Kx8 and 256Kx8 ROM address decoding function.
For a 8Kx8 ROM application, the upper 19 bits of this register correspond to the upper 19 bits of the expansion
ROM base address. The lower 13 bits of this register correspond to the size of the expansion ROM. Those bits
correspond to the size of the expansion ROM are determined by MCR bit 5, bit 6 and bit 7 and can not be
writable by the system configuration write command. The device independent configuration software can only
determined the bits corresponding to the base address. The following table describe the relationship between
the addressing bus, sizing bits and the MCR bit 5/6/7.
MCR.7
0
0
0
1
1
1
1
MCR.6
0
1
1
0
0
1
1
MCR.5
X
0
1
0
1
0
1
Addressing Bits
None
31~13
31~14
31~15
31~16
31~17
31~18
Sizing Bits
None
12~0
13~0
14~0
15~0
16~0
17~0
ROM Size
No BOOT ROM
8Kx8
16Kx8
32Kx8
64Kx8
128Kx8
256Kx8
The device independent configuration software can only determined the addressing bits. The bit 0 of the ROM
base address register will be reset "0" by W89C940 if the MCR is set as "No BOOT ROM", i.e. BPS0=0,
BPS1=0 and BPS2=0. The bit 0 of the ROM base address register will be set "1" if the MCR is programmed as
there is an expansion ROM device add-on the LAN adapter. The initial value of FFFF8001H indicates that there
is a 32Kx8 expansion ROM device existing. The initial value is changed according to the BOOT ROM size
selection in the MCR (Mode Configuration Register).
Interrupt Line Register
This register is a readable and writable register. The POST software of system could write the routing
information into this register as it initializes and configures the system. The value in this register tells which
input of the system interrupt controllers the device's interrupt pin i connected to. Device drivers and operating
systems can use this information to determine priority and vector information. For x86 based PCs, the value in
this register correspond to IRQ numbers (0-15) of the standard dual 8259 configuration. The value 255 is
defined as meaning "unknown" or "no connection" to the interrupt controller. Values between 15 and 255 are
reserved.
Interrupt Pin Register
The W89C940 use the INTA# as its interrupt pin. The content of this register is fixed into "01".
Min-Gnt Register
It is used for specifying how long a burst period the device needs assuming a clock rate of 33MHz. The content
of this register will be updated after power on by the EEPROM load operation. The Min-Gnt should be
programmed into the 17th byte of the EEPROM for power on auto loading.
相關PDF資料 |
PDF描述 |
|---|---|
| W89C982 | INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | INTEGRATED MULTIPLE REPEATER II |
| W8NB80 | N - CHANNEL 800V - 1.2ohm - 7.5A - TO-247 PowerMESH MOSFET |
| W90100F | Embedded Micro-Controller(32位嵌入式的微控制器) |
| W90210F | PA-RISC Embedded Micro-Controller(惠普PA-RISC結構的32位嵌入式微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W89C940F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10M PCI-Bus Ethernet Network Interface Controller |
| W89C982 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
| W89C982AF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:INTEGRATED MULTIPLE REPEATER II |
| W8C2-DNL | 制造商:Hwei Lung Precision Machinery 功能描述:TORCH 8 LED BLACK 2C |
| W8D10PF29033 | 制造商:TE Connectivity 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。